Heating, AC & Water Heater Services in Lakewood, OH

Completed routine HVAC cooling system maintenance including inspection of basement ductwork infrastructure and air filtration system. Replaced 16x25x5 pleated air filters in the metal housing unit to ensure optimal airflow and system efficiency for the upcoming cooling season.

Completed comprehensive cooling system maintenance on residential HVAC unit. Performed inspection of outdoor condensing unit electrical components including CoreSense compressor diagnostic device, capacitor connections, and control wiring; verified all electrical connections were secure and properly terminated. Inspected indoor air handling equipment and ductwork in mechanical room, confirmed proper mounting and clearances of all components. System tested and operating within normal parameters.

Completed comprehensive cooling system maintenance on residential HVAC unit. Inspected blower assembly and found moderate dust accumulation on squirrel cage fan blades, which was cleaned to restore optimal airflow efficiency. Performed electrical diagnostics on outdoor condensing unit using digital multimeter, verifying voltage readings and confirming proper system operation at 497.8 volts on tested circuit.

Replaced existing 100-amp electrical service panel with new code-compliant installation per NEC requirements. Installation included four combination smoke/carbon monoxide detectors hardwired to the panel and integrated whole-house surge protection device. All circuit breakers were properly installed and labeled, with organized wire routing including main service conductors, neutral bus connections, and ground bar terminations. Panel was mounted on exterior with appropriate weather-resistant enclosure and conduit connections for service entrance cables.

Completed preventive maintenance on dual HVAC system including furnace and outdoor condensing unit. Performed comprehensive inspection of furnace components including blower motor assembly, heat exchanger, burner assembly, electrical connections, and gas piping with all connections secure and operating within normal parameters. Inspected outdoor condenser unit, verified proper airflow through louvers, checked refrigerant lines, and noted accumulation of leaves and debris around unit pad requiring cleanup for optimal system performance.

Completed comprehensive HVAC cooling and heating maintenance on dual-system Goodman residential installation located in basement utility area. Performed standard seasonal maintenance procedures including inspection of furnace unit, air handler, refrigerant lines, electrical connections, and ductwork throughout the system. All components were found to be operating within normal parameters, with ductwork and connections properly secured along brick wall routing and throughout the installation area.

Completed outdoor air conditioning unit installation on exterior brick wall with proper refrigerant line routing, electrical conduit installation, and equipment mounting on concrete pad. Performed system pressure testing and verification using digital manometer to ensure proper refrigerant charge and system operation within manufacturer specifications.

Conducted on-site evaluation for mini split system installation options in residential property with existing boiler heating system. Assessed basement utility area and adjacent room with wood paneling to determine optimal equipment placement and review space constraints for proposed ductless mini split configuration.

Conducted on-site evaluation of existing residential HVAC system per customer request for cooling system replacement estimate. Assessed current furnace and air conditioning equipment, documenting existing thermostat configuration and furnace installation with exposed internal components including blower motor assembly, gas valve connections, and control wiring. Provided comprehensive replacement options for complete system upgrade to address reported cooling system failure.

Performed preventative maintenance tune-up on wall-mounted mini split system. Opened unit housing to access evaporator coil assembly, inspected internal components including heat exchanger fins and wiring connections. Removed and cleaned two curved mesh filters that had accumulated significant dust and debris, restoring proper airflow to the system.

Completed comprehensive heating maintenance on residential furnace system. Performed thorough inspection of all internal components including heat exchanger, burner assembly, blower motor, and control boards. Cleaned burners, checked gas pressure, tested ignition sequence, and verified proper operation of all safety controls. Inspected ductwork connections and confirmed adequate airflow throughout the system. All components found operating within manufacturer specifications and unit left in proper working condition.

Returned to property to complete repair by replacing faulty control board and igniter on HVAC system. Both components were successfully installed and system was tested to verify proper operation and functionality.

Completed scheduled heating maintenance on residential gas furnace system. Performed comprehensive inspection of all major components including heat exchanger, burner assembly, and flame sensors. Verified proper operation of ignition system with multiple flame sensors functioning correctly. Inspected electrical connections, control board, and wiring throughout unit - all connections secure and operational. Checked venting system including PVC intake and exhaust pipes for proper installation and clearances. Tested furnace operation through full heating cycle, confirming reliable ignition, steady flame pattern, and proper shutdown sequence. All safety controls and limit switches tested and operating within manufacturer specifications. System running efficiently with no issues identified.

Diagnosed and resolved an issue with the upstairs zone overheating beyond set temperature, where the system was heating to 82°F despite being set to 67°F. Inspected the White-Rodgers thermostats and replaced two faulty vents to restore proper temperature control functionality.

Performed scheduled maintenance service on dual heating systems, including inspection and testing of water boiler and furnace components. Verified proper operation of circulation pump, checked valve functionality, and examined copper piping network for leaks or corrosion issues. Noted minor discoloration at wall junction requiring future monitoring but systems are operating within normal parameters.

Conducted comprehensive assessment for complete home rewiring. Inspected existing electrical service panels, including main disconnect and circuit breaker configuration. Evaluated current wiring infrastructure, water heater connections, and mechanical room electrical components to determine scope of necessary rewiring work.

Performed scheduled boiler tune-up, removing and inspecting thermocouple assembly which showed signs of wear. Identified blockage in boiler drain requiring service; documented condition with photos and prepared updated estimate for drain clearing as previous recommendation had been made.

Performed routine heating system maintenance including electrical component inspection and static pressure testing. Circuit board connections were verified intact with no loose wires, and system pressure readings were measured at 36.4 (within normal operating parameters) using Klein Tools digital manometer.

Performed scheduled maintenance on residential heating system, including diagnostic testing of furnace controls and electrical components. Inspected internal wiring connections and drain assembly for proper operation, with all components found to be functioning within manufacturer specifications.

Responded to service call for toilet intermittently running. Inspected toilet components and water supply line. Identified and repaired faulty flush valve mechanism causing continuous water flow. Tested toilet operation after repair to confirm proper functioning.