HVAC & Air Quality Services in Mayfield Heights, OH

Conducted comprehensive electrical inspection of main service panel and adjacent electrical installation. Documentation included detailed photography of circuit breakers, wiring configuration, and conduit routing. Identified several circuits with handwritten tags and noted areas requiring attention as indicated by "CIRCUITS OFF!" warning.

Performed scheduled heating maintenance service on furnace system. Inspected internal components including blower motor, wiring connections, and electrical assemblies. Conducted gas pressure testing with digital manometer showing 2.43" WC, confirming system is operating within manufacturer specifications.

Successfully installed a new Rinnai tankless water heater in basement utility area, including proper venting with PVC pipes through ceiling joists, connection of copper supply lines, and installation of required valves. Unit was mounted securely on wall and all connections were tested to verify proper operation of the system.

Diagnosed loud grinding noise in Rinnai tankless water heater during operation. Inspection revealed faulty flow control motor (MP36GU 12VDC) with worn components. Replaced flow control motor assembly and verified proper operation with no further noise during heating cycles.

Performed routine heating maintenance on residential HVAC system. Inspected and verified proper wiring connections to blower motor assembly and control module. Checked all components including refrigerant lines, gas connections, and safety controls for proper operation with no issues found.

Conducted a comprehensive plumbing inspection with focus on two wall-mounted tankless water heaters that customer reported as non-functioning. Systems were examined along with associated piping, valves, expansion tank, and ventilation components in basement utility area. Visual inspection completed with photographic documentation of the installation setup for further analysis.

Completed scheduled heating maintenance on Goodman furnace system. Performed diagnostic testing with digital meter, recording voltage reading of 35.4V at control board. Inspected ductwork, condensate drainage system, and electrical connections - all components functioning within normal parameters.

Conducted full system evaluation of existing Carrier HVAC equipment in utility closet. Inspected furnace with front panel open to assess internal components including control board, wiring and mechanical elements. Documented condition of ductwork, connections, and adjacent water heater to prepare comprehensive system replacement options for client consideration.

Successfully installed a new Goodman 80% efficiency furnace in basement utility area, including proper connection of metal ductwork, PVC drain lines, and exhaust venting. System was fully tested and is operating according to manufacturer specifications.

Performed scheduled tune-up on heating system in residence built circa 2005 with original equipment. Inspection revealed significant dust accumulation on components including evaporator coil, copper refrigerant lines, and control wiring. Thoroughly cleaned system to restore proper airflow and efficiency.

Completed heating system maintenance inspection following customer concern about ice buildup on exhaust during recent cold weather. Inspected electrical panel and discovered moderate corrosion on copper bus bar connections. Documentation included photographs of the electrical panel showing circuit breakers, wiring condition, and the affected components for reference.

Conducted a comprehensive evaluation of the full HVAC system replacement options for customer. Documented existing equipment including Type B combustion components, motor/pump assembly, and associated ductwork with service records. Photographed and cataloged system components including equipment identification (C2) for accurate replacement specifications.

Performed scheduled preventative maintenance on residential furnace system. Inspected blower assembly and heat exchanger, finding moderate dust accumulation on ventilation components. Cleaned fan blades and air intake grills to ensure proper airflow and system efficiency.

Responded to service call for boiler not providing adequate heat and displaying pressure warning message. Performed diagnostic inspection of internal components, including pressure sensors, connectors, and circulation system. Adjusted system pressure to manufacturer specifications and verified proper operation of all safety controls before confirming normal heating function restored.

Responded to service call for water heater with no hot water. Diagnosed pilot light failure on tanked water heater system. Successfully relit pilot light, tested system operation, and confirmed proper functioning of expansion tank and associated copper piping.

Completed scheduled heating system tune-up maintenance on an 8-year-old unit. System was thoroughly inspected, cleaned, and calibrated to ensure optimal performance for the heating season. Customer expressed interest in reviewing Maintenance Value Plan options for future service coverage.

Conducted furnace replacement consultation for client with existing older HVAC system. Inspected current installation including water heater configuration in utility area and evaluated existing thermostat (battery-operated model displaying 25°). Presented replacement options for furnace while noting AC unit is also aging but not prioritized by client due to minimal usage.

Diagnosed short cycling issue in aging furnace system. Inspection revealed severe dust accumulation on blower wheel and heat exchanger components, restricting proper airflow. Performed comprehensive cleaning of blower assembly and verified proper operation after service, resolving the cycling problem.

Conducted comprehensive assessment of existing water boiler system and provided three-tier replacement options (Good/Better/Best) for conversion to gas HVAC system. Documented current installation including gas line with visible corrosion, associated plumbing connections, and verified electrical panel configuration with dedicated circuit breakers for HVAC equipment. Presented customer with energy efficiency options ranging from 80% to 96% AFUE for heating and 13.4 to 16 SEER for cooling capacity.

Performed heating maintenance including combustion analysis with Testo 310 showing 15.0% O2 and 6ppm CO readings. Inspected blower motor assembly and wiring connections. Verified customer's filter dimensions were incorrect and assessed non-functioning humidifier causing excessive dryness in home.