Trusted Heating, Air Conditioning & Plumbing Services in Beachwood, OH

Replaced defective low pressure switch under warranty on HVAC system. Unit tested and verified proper operation with refrigerant lines and valve assembly functioning correctly upon completion.

Completed routine cooling system maintenance on outdoor condensing unit. Inspected electrical components including contactor, capacitor, and control board; verified all wire connections were secure and properly terminated. Cleaned exterior louvers and grille to ensure adequate airflow through the unit. All components found in good operating condition with normal wear consistent with outdoor installation.

Completed scheduled preventive maintenance on residential split-system air conditioning unit. Performed comprehensive inspection of indoor Amana furnace with cooling coil and outdoor condensing unit. Checked refrigerant pressures, verified proper airflow, inspected electrical connections and controls, tested thermostat operation, and cleaned condenser coils. All components found operating within manufacturer specifications with no deficiencies noted.

Completed HVAC equipment estimate for replacement of existing residential furnace system located in utility closet. Evaluated current beige furnace unit with exposed internal components including compressor assembly and gas valve connections. Provided customer with options for Lennox high-efficiency replacement unit to upgrade from current equipment. Documented existing installation configuration including ductwork connections, electrical wiring, and proximity to water heater for accurate replacement planning and sizing requirements.

Responded to a no-cool complaint on a 16-year-old Lennox rooftop unit at a condo with two side-by-side RTU installations. Accessed the units via ladder, performed diagnostic assessment, and documented existing mechanical infrastructure including aged copper refrigerant lines, PVC condensate piping, flexible ductwork connections, and associated plumbing components showing typical wear and oxidation consistent with unit age. Provided estimate for complete RTU replacement.

Completed seasonal cooling tune-up on outdoor condensing unit. Performed system diagnostics using digital manifold gauges to verify refrigerant pressures and temperatures, inspected copper line set and service valves for proper operation, and confirmed condensate drain system functionality. All components operating within manufacturer specifications with no issues identified.

Conducted comprehensive estimate for full HVAC system replacement in residential basement location. Evaluated existing furnace unit and ductwork system, documented current equipment condition showing age-related wear and dust accumulation on components, and presented multiple replacement options to address repair needs. Provided detailed assessment and recommendations for complete system upgrade.

Completed scheduled preventive maintenance on residential cooling system equipped with Copeland scroll compressor. Performed comprehensive inspection of outdoor condensing unit, verifying proper operation of CoreSense diagnostic module with no active fault codes or alarm conditions present. Confirmed condenser coil cleanliness, checked refrigerant line connections at service ports, verified capacitor mounting and electrical connections secure, and documented system operating within normal parameters.

# Mini Split System Diagnostic and Repair Responded to service call for non-operational mini split cooling system. Property has two mini split units aged 9 and 11 years respectively. Upon arrival, performed comprehensive diagnostic testing on both outdoor condensing units and indoor air handlers. Utilized digital multimeter to test electrical components on the Trane XE 1000 outdoor unit. Measured voltage and amperage at compressor, contactor, and capacitor to identify potential electrical failures. Noted significant weathering and debris accumulation on outdoor unit surfaces, including biological growth on top panel which can impede heat transfer efficiency. Inspected refrigerant line sets connecting outdoor units to indoor air handlers. Verified integrity of insulation on copper refrigerant lines running through basement utility area. Checked for refrigerant leaks using appropriate detection methods at all connection points and service valves. Evaluated indoor furnace and air hand

Completed scheduled preventative maintenance on residential cooling system. Upon arrival, found significant dust and debris accumulation on ventilation grille with visible cobwebbing and possible mold growth, indicating extended period without service. Thoroughly cleaned all accessible components and tested system capacitance readings using digital multimeter, confirming proper electrical function at 44.65 μF. Unit restored to optimal operating condition.

Responded to complaint of air conditioning system failing to maintain setpoint, with thermostat set at 72°F but space temperature reading 78°F. Inspected HVAC system and return air plenum, noting Air Scrubber purification system installed and operational. Removed and inspected air filtration array, documenting filter condition with photographs. Customer reported filter was recently installed during previous visit and system had minimal runtime over two-week period since installation. Verified system components and documented current operating conditions for follow-up evaluation.

# HVAC Cooling Maintenance - Two System Service Completed comprehensive preventive maintenance service on two cooling systems as part of ongoing recurring maintenance program. Performed thorough inspection of both units, including examination of condenser coils, heat exchanger components, and airflow pathways. First system inspection revealed stock unit #813 with proper airflow direction labeling intact. Noted moderate corrosion present on metal framework and support structures, consistent with normal aging and environmental exposure. Heat exchanger fins and ribbed components inspected and found operational, though frame deterioration documented for monitoring. Second unit presented with significant dirt accumulation and debris buildup on exterior grille and louvers. Dark streaking and grime visible throughout horizontal slat assembly, with concentrated soiling in airflow channels. Condenser coils behind grille showed dust and debris infiltration. External housing mounted on buildi

Responded to service call for clogged and leaking air conditioning system. Upon inspection, identified blockage in condensate drain line causing water backup and leakage. Cleared obstruction from drain line, replaced damaged pipe coupling, and verified proper drainage flow. Inspected both outdoor condenser units for proper operation and confirmed system returned to normal functioning without further leaks.

Responded to callback for 7-year-old AC unit with persistent low airflow issue following previous repair attempt. Performed comprehensive diagnostic testing using digital multimeter and pressure gauges to assess system performance and identify root cause of inadequate air delivery. Measurements indicated abnormal readings requiring further investigation of air handler components and refrigerant pressures to restore proper system operation.

Conducted estimate visit for complete HVAC system replacement at residential property. Assessed existing 27-year-old air conditioning unit and Ruud furnace system located in basement, both of which have reached end of service life. Documented current equipment configuration including ductwork layout, air handler placement, and existing installation setup through photographic documentation. Provided comprehensive replacement quote for new air conditioning and furnace system to address failed cooling equipment and aging heating components.

Performed comprehensive cooling season tune-up on residential HVAC system. Inspected and verified blower wheel assembly condition, confirmed proper operation and cleanliness of squirrel cage blower with no significant debris accumulation. Conducted electrical diagnostics on outdoor condensing unit using clamp meter, measured and recorded amperage readings to verify compressor and system performance within manufacturer specifications.

Completed installation of new air conditioning system including indoor air handler unit with integrated control board, capacitor, and electrical components. System was properly wired, refrigerant lines connected to copper fittings, and ductwork integrated with existing infrastructure. All electrical connections were secured, control board tested for proper operation, and unit commissioned to manufacturer specifications with balance payment collected upon completion.

Replaced failed dual-run capacitor with new TOTALINE P291-7054R unit rated at 70/5μF, 440VAC. Installed surge protection devices on both indoor air handler and outdoor condensing unit to protect control boards and compressor from voltage spikes and power surges.

Conducted on-site assessment for mini-split installation to provide climate control for select areas of the residence. Evaluated existing electrical panel capacity and documented current breaker configuration to determine compatibility with proposed ductless system requirements.

Completed scheduled cooling system maintenance on residential HVAC unit. Inspected air handler components and verified proper operation of filtration system. Measured supply air temperature at 53.8°F, confirming adequate cooling performance. Noted hose replacement requirement for future service attention.