HVAC & Plumbing Services in Cleveland, OH

Responded to no cooling complaint at residential property. Upon arrival, accessed HVAC system through side entrance as requested and conducted diagnostic evaluation of heating and cooling equipment. Inspected furnace, ductwork, and air handler assembly in mechanical room. System components showed signs of normal wear but no immediate visible damage to primary equipment. Documented existing conditions of HVAC installation including main supply ductwork, exhaust piping, and air handler configuration. Assessed airflow pathways and ventilation system integrity. Customer reported complete loss of cooling function requiring further diagnostic testing to identify root cause of system failure.

Responded to tankless water heater displaying Salt 11 error code on digital display panel. Diagnosed error condition, performed necessary system diagnostics and maintenance procedures to clear fault code and restore unit to proper operation. Verified all water connections, gas line connections, and safety valves functioning correctly upon completion of service.

Completed scheduled HVAC cooling system maintenance on aging unit with OPP furnace configuration. Performed comprehensive system inspection, documented temperature readings at 54.2°F, and evaluated electrical components including relay and contactor within the control panel. All maintenance procedures completed per manufacturer specifications for systems over 10 years old.

Completed comprehensive cooling system maintenance on HVAC unit. Inspected and photographed return air vent grilles, noting accumulated dust and debris within louvers and slat openings. System operational and performing within normal parameters following standard maintenance protocol.

Responded to no-power furnace call resulting from previous basement flooding caused by hail storm damage. Gas company had previously shut off unit as a safety precaution. Conducted visual inspection of blower motor assembly and control board, documenting existing conditions with photos. Control board showed signs of age with visible discoloration and oxidation on circuit board surface, though electronic components including relays, resistors, and capacitors remained intact. Blower motor assembly and electrical connections appeared functional with no visible flood damage to these components. Appointment scheduled for follow-up service when family member can be present for complete system evaluation and restoration.

Replaced failed condensate pump on residential air handler unit. Installed new pump assembly and verified proper drainage function through white PVC condensate lines to prevent water overflow and potential equipment damage.

Conducted comprehensive site assessment for central air conditioning system installation at property currently equipped with forced air furnace heating only. Evaluated existing electrical infrastructure, documenting 50-amp circuit breaker panel and main distribution panel condition. Inspection revealed significant corrosion and white powdery deposits throughout electrical panel, indicating potential moisture intrusion and deteriorated connections requiring attention prior to AC installation. Photographed weathered wooden framing around electrical equipment and documented current electrical capacity to determine compatibility with proposed cooling system requirements. Provided customer with add-on options and equipment recommendations for integrating new air conditioning system with existing forced air heating infrastructure.

Performed routine maintenance inspection on commercial rooftop gravity furnace unit at restaurant facility per customer request. Conducted thorough operational assessment of the HVAC system, verified proper functioning of all components, and confirmed unit is operating within manufacturer specifications.

Installed a Chateau Chrome pressure-balance valve (model L2353) in the bathroom bathtub assembly. The new chrome-plated single-handle control valve was mounted on the tiled wall above the tub spout, replacing the existing fixture to ensure proper water temperature regulation and flow control.

Completed routine cooling system maintenance on ductless mini-split air conditioning unit. Performed filter inspection and cleaning, accessing internal mesh filter assembly which was found in good operational condition. Inspected condensate drain system components including drain port and trap assembly, removing accumulated debris to ensure proper drainage function. All system components examined and verified to be operating within normal parameters with no deficiencies noted.

Conducted site assessment for commercial heating system replacement estimate. Documented existing electrical infrastructure including main breaker panel configuration and available circuits to determine power requirements for new heating equipment. Inspected exterior mechanical area and existing HVAC equipment location, noting building access points and installation pathway considerations for equipment replacement.

Replaced evaporator coil under install warranty. Evacuated refrigerant from system, removed defective coil, and installed new replacement unit. Pressure tested system for leaks, evacuated to proper vacuum levels, and recharged with manufacturer-specified refrigerant quantity using calibrated scale. Verified proper system operation and temperatures upon completion.

Responded to no cooling call at residential property. Upon arrival, found outdoor condenser unit heavily overgrown with vegetation restricting airflow. Removed access panel and performed system inspection. Identified non-functional compressor and contactor requiring replacement. Cleared vegetation from around unit to restore proper airflow and accessibility for service. System evaluated and customer advised of necessary repairs to restore cooling operation.

Responded to emergency service call for non-operational geothermal system with water overflow condition causing flooding in mechanical room. Upon arrival, found extensive water accumulation on basement floor surrounding geothermal heat pump equipment. Performed diagnostic testing using digital multimeter to assess system controls and electrical components. Opened access panels on air handler unit to inspect internal circuitry, control boards, and wiring for water damage or electrical faults. Identified source of water overflow and addressed flooding issue to restore system operation and prevent further water damage to mechanical equipment and basement area.

Performed scheduled preventive maintenance on HVAC cooling system control board and electrical components. Inspected printed circuit board assembly, verifying proper operation of integrated circuits, capacitors, resistors, and all surface-mounted components. Examined all wire connections including line voltage, transformer, and thermostat terminals to ensure secure attachment and proper routing. Confirmed emergency stop switch functionality and verified all terminal connections were tight and free of corrosion.

Responded to failed boiler inspection due to critical electrical wiring violations in basement mechanical room. Line voltage wiring was improperly connected to water line, and low voltage wiring was incorrectly attached to gas line, creating serious safety hazards. Documented existing conditions with photographs showing the tankless water heater installation, copper piping network, electrical conduit routing, and control panel configuration to support warranty claim and code compliance requirements.

Conducted on-site electrical assessment for whole-house generator installation. Evaluated existing 200-amp main service panel (Thomas brand) and exterior meter base configuration to determine compatibility and transfer switch placement requirements. Documented current electrical infrastructure including main breaker panel layout, circuit distribution, exterior meter housing location, and available conduit pathways along building exterior for future generator connection and automatic transfer switch installation.

Performed comprehensive cooling system maintenance on a 9-year-old air conditioning unit. Conducted electrical diagnostics using digital clamp meter to verify proper amperage draw and system performance. Inspected condenser unit components, cleaned coils, and confirmed operational efficiency of outdoor unit and fan assembly.

Conducted on-site consultation for furnace replacement options. Evaluated existing HVAC system including indoor furnace installation in attic space and outdoor condensing unit positioned on concrete pad against exterior brick wall. Documented current equipment configuration and discussed available replacement solutions with homeowner to address heating system needs.

Completed scheduled preventive maintenance on residential cooling system as part of ongoing service agreement. Performed comprehensive inspection of evaporator coil assembly and heat exchanger fins, noting minor dust accumulation on coil surfaces and supply register. Verified proper airflow through ventilation grilles and documented system condition through photographic records. All components found operating within normal parameters with no immediate service needs identified.