HVAC & Air Quality Services in Shaker Heights, OH

Performed comprehensive maintenance on residential heating system. Conducted electrical testing with multimeter showing 231V reading at unit terminals. Accessed ceiling-mounted air handler using extension ladder and inspected internal components including wiring connections and PVC condensate lines.

Performed routine heating maintenance including inspection of system components. Found filter heavily loaded with dust and debris requiring replacement. Conducted static pressure testing with digital manometer, measuring 3.70 inH2O, which indicates potential airflow restrictions in the system.

Performed routine maintenance on tanked water heater system located in utility room. Inspected all connections, valves, and components with special attention to the damper assembly and associated copper piping. Visual inspection confirmed proper installation with no signs of leaks or deterioration; system is functioning as intended.

Conducted plumbing inspection of water supply system in utility area. Identified significant corrosion at pipe-floor junction with visible greenish-blue oxidation and orange staining on concrete, indicating active leak or condensation issues. Documented condition of pressure regulator/valve assembly and electrical conduit installation for follow-up service.

Performed scheduled maintenance on aging HVAC heating system located in basement utility area. Inspected and cleaned copper heat transfer components showing normal wear. System includes furnace unit with connected ductwork, flue piping, circulation pump assembly, and associated valves all functioning within acceptable parameters.

Responded to service call regarding water leakage from humidifier after customer replaced water panel. Inspection revealed significant damage to the humidifier control panel with multiple burn/melt holes compromising the unit's integrity. Replaced damaged control panel and verified proper operation with no further leakage.

Performed routine maintenance service on boiler system, inspecting heat exchanger components showing signs of oxidation and rust formation. Examined copper piping connections and metal components of the heating system, documenting current condition with photos for maintenance records.

Performed scheduled maintenance on boiler system in utility room, including inspection of pressure gauge readings, valves, and pipe connections. Conducted diagnostic testing using multimeter on furnace unit and verified proper operation of all components. System was left in good working condition with all connections secure and operating parameters within normal range.

Performed scheduled heating maintenance on boiler system. Inspected sight glass flow indicator on MAF valve and noted rust developing on iron piping components. Observed significant dust accumulation within equipment housing requiring cleaning; recommended regular maintenance to prevent further deterioration.

Performed scheduled boiler maintenance service on water heating system. Inspected aging copper piping showing oxidation at joints, checked pressure readings, and examined the blue cabinet housing with exposed wiring. Noted minor corrosion on metal components and previous water staining at unit base, but system remains functional after service.

Completed installation of a Goodman 96% efficiency furnace with matching AC system. System includes properly connected ductwork with sealed plenum, PVC venting, and all required electrical components including Edison ECNR50 fuses for protection. Final inspection verified proper operation with all safety features functioning correctly.

Completed rewiring of first floor thermostat with direct connection to furnace, bypassing the existing HZ311 zone control panel. Multiple colored control wires were properly terminated at appropriate terminals to restore proper heating system functionality.

Responded to emergency water leak call where customer reported water leaking through first floor ceiling. Upon inspection, identified significant ceiling damage with exposed wooden structural elements. Investigated source of leak despite no bathroom directly above affected area, determined cause, and completed necessary repairs to prevent further water damage to ceiling and crown molding.

Performed routine maintenance on boiler system, inspecting pressure gauge readings and verifying proper operation of control components. Accessed furnace interior to examine electrical connections and wiring integrity, and checked copper supply lines for signs of leaks or corrosion.

Conducted comprehensive inspection of aging plumbing system with significant corrosion observed on multiple valves and pipe connections. Documented extensive deterioration including peeling paint, exposed materials, and possible moisture damage to surrounding walls and ceiling. Photos taken of all affected areas to support quotation for recommended repairs and potential system replacement.

Successfully installed AprilAire Model 60 humidifier system with PVC drainage piping and clear tubing for proper water flow. Unit was calibrated, tested, and confirmed operational with humidistat displaying 32% relative humidity and green "Humidifier On" indicator illuminated.

Inspected boiler system and identified severe corrosion at copper pipe elbow joint in basement utility area. Documented significant deterioration at the pipe junction where copper connects to black pipe via metallic coupling, showing signs of potential leakage and material breakdown requiring immediate attention.

Responded to no-heat call for a relatively new boiler system. Diagnosed communication failure between thermostat and boiler control unit. Observed normal blue flame operation at burners but detected significant corrosion along the heat exchanger, indicating possible condensate drainage issues affecting electrical components. Restored communication functionality and verified proper system operation.

Completed installation of a 5-head mini-split system with 2 Daikin condensers mounted on concrete pads. Performed pressure testing with Testo 568s digital gauge to verify system integrity, achieving 502.5 psi during leak detection procedures. System was properly installed with coordination with electrical contractor for final connections.

Conducted assessment of existing boiler system and presented repair options to client. Inspected galvanized ductwork in utility area, noting connection points requiring attention. Examined PVC plumbing configuration and ventilation components to determine optimal heating solution.