Air Conditioning & Heating Services in Willoughby, OH

Performed comprehensive maintenance and repair on HVAC system experiencing reduced efficiency due to severe contamination. Disassembled and thoroughly cleaned blower wheel to restore proper airflow. Performed complete coil cleaning on heavily soiled condenser unit, removing extensive dirt, debris, and biological growth that had accumulated throughout the fin surfaces and was significantly impacting system performance. Replaced all 24-volt contactors and installed new run capacitor to ensure reliable electrical operation and proper compressor function.

Completed preventative maintenance on two cooling systems. Inspected electrical connections at contactor assembly, verified proper wire termination and secure mounting of all components. Measured and documented supply air temperature at 66.1°F, confirming system operation within normal parameters.

# HVAC Cooling Maintenance Summary Completed scheduled preventive maintenance on residential split-system air conditioning unit. Performed comprehensive inspection of outdoor condenser unit, verifying proper operation of compressor, fan motor, and electrical components. Checked refrigerant levels and system pressures within manufacturer specifications. Cleaned condenser coils and cleared debris from unit perimeter to ensure optimal airflow and heat exchange efficiency. Inspected condensate drainage system including PVC drain lines for proper flow and verified no blockages present. Examined electrical connections, contactor operation, and capacitor functionality. All components operating within normal parameters. System cooling effectively with no immediate service needs identified.

Performed routine maintenance flush on Reeves brand tankless water heater unit. Completed descaling procedure by circulating cleaning solution through the heat exchanger to remove mineral buildup and scale deposits. Isolated unit using service valves, connected flushing equipment, and ran cleaning cycle per manufacturer specifications. Inspected all copper supply and return lines, verified proper operation of isolation valves, and checked digital control display for error codes. Confirmed unit returned to normal operating parameters upon completion. System tested and operating efficiently.

Performed comprehensive cooling system tune-up on residential HVAC unit located in basement utility room. Completed standard maintenance procedures including inspection of furnace unit, refrigerant lines, ductwork connections, and overall system operation to ensure optimal performance for the cooling season.

Returned to property for copper piping installation following burst pipe repair. Previous visit in January identified the need for wall removal to access affected areas. Upon arrival, confirmed that drywall had been removed as requested, exposing ceiling joists and structural framing. Documented exposed wooden beams, rafters, and parallel joists in preparation area. Verified access points were adequate for copper pipe replacement work. Photographed ceiling cavity showing weathered structural elements and newly accessible areas where piping installation will occur. Work area is now properly prepared for the copper piping installation to proceed.

Completed routine cooling maintenance on aging HVAC system, including replacement of 16x25x4 pleated air filter and comprehensive electrical diagnostics of outdoor condenser unit. System tested and verified operational with all measurements within acceptable parameters for continued reliable performance.

Completed comprehensive HVAC cooling system maintenance inspection. Verified proper system operation by measuring supply air temperature at 49.6°F and monitoring electrical parameters including amp draw of 0.057A and voltage reading of 106.2V. All measurements indicated normal operating conditions with adequate cooling performance and proper electrical function.

Conducted comprehensive evaluation of existing HVAC system for replacement estimate. Documented outdoor condensing unit positioned against exterior wall with refrigerant lines running along ground through landscaping area. Assessed indoor air handler unit installed in attic space, noting ComfortMaker equipment with accessible filter location marked on cabinet. Photographed both components to provide visual documentation of current system configuration, equipment condition, and installation environment for replacement options analysis.

Completed comprehensive preventive maintenance on residential forced-air heating system. Performed thorough inspection of furnace cabinet, blower motor assembly, and all electrical connections. Verified proper operation of control board, checked wire terminations and safety interlocks, and confirmed all warning labels were intact and legible. Inspected ductwork, humidifier unit, and condensate drain lines throughout mechanical room for proper installation and functionality. All components found operating within normal parameters with no immediate service needs identified.

Completed routine heating maintenance on vertically-mounted air handler unit in basement utility area. Performed comprehensive system inspection including filter check, electrical connections verification, blower motor assessment, and condensate pump operation. All components found to be in proper working order with accessible panels for ongoing maintenance needs.

Completed scheduled heating maintenance on HVAC system. Performed comprehensive inspection of furnace unit, including examination of heat exchanger, burner assembly, and internal electrical components. Verified all wire connections were secure and properly routed throughout the equipment compartment. Inspected condensate drain system, noting PVC drainage piping and safety port valve in proper working condition. Observed evidence of mineral deposits and condensation staining on drain pan surface, typical of normal system operation. Checked insulation on refrigerant lines and condensate tubing for integrity. All system components found operating within manufacturer specifications with no immediate service requirements identified.

Completed routine heating maintenance on a Goodman residential furnace system. Performed comprehensive inspection of the unit, ductwork connections, gas line assembly with shutoff valve, and associated HVAC components to ensure proper operation and safety compliance. All systems checked and found to be functioning within normal parameters.

Performed routine heating system maintenance including pressure testing with digital manometer (reading 644E) on ductwork and inspection of insulation panels. All components were found to be in normal operating condition with expected wear patterns; no repairs required at this time.

Conducted site assessment for mini-split installation options in residential garage space. Garage houses a vehicle and recreational equipment with multiple storage systems. Will provide suitable heating/cooling options based on layout constraints and customer usage patterns.

Performed scheduled heating maintenance service on furnace system. Inspected and documented condition of air filter showing moderate dust accumulation with yellow discoloration concentrated at lower portion. Examined evaporator coil housing and filter assembly, noting proper installation of diamond-pattern filtration media within metal frame housing.

Inspected client's dryer circuit due to reported 220V line malfunction. Performed comprehensive evaluation of electrical panel, specifically examining the double-pole breaker serving the dryer. All connections were verified and breaker functionality was tested to restore proper power supply to the dryer circuit.

Completed warranty service to replace furnace door as requested. Inspected HVAC system components including ductwork connections and ventilation pipes. Changed customer-supplied air filter during visit as requested.

Installed a flow restrictor valve in the basement plumbing system to reduce excessive water pressure to the shower. Adjusted and tested the system to ensure proper flow rate, resolving the high-pressure issue that was affecting shower performance.

Completed installation of a new sump pump system in basement utility area, replacing the previous unit which showed significant rust and corrosion. Installation included proper connection of PVC discharge pipes, check valve installation, and verification of system operation to ensure effective basement water management.