Heating, AC & Plumbing Services in Moreland Hills

Completed scheduled heating maintenance on two furnace systems as part of ongoing preventive maintenance program. Performed comprehensive system inspections including combustion analysis using flue gas analyzer, which confirmed efficient operation with readings of 93.7°F flue temperature, 69.7% efficiency, and safe 1 PPM carbon monoxide levels on natural gas equipment. Inspected blower wheel assembly, verified clean condition of squirrel cage fan with no debris accumulation, and confirmed proper motor operation and airflow components functioning within normal parameters.

Performed comprehensive HVAC cooling system maintenance on window unit. Conducted electrical diagnostics using clamp meter, measuring amperage draw at 2.93A and voltage at 0.028V to verify proper system operation. Inspected and tested capacitor with connected yellow, purple, and red/brown wiring, confirming secure terminal connections and proper mounting bracket integrity. All electrical components showed normal operation with no signs of damage, corrosion, or unusual wear, and system is functioning within manufacturer specifications.

# HVAC Furnace Installation Successfully installed a two-stage ECM 80/90 furnace system in basement utility area. The installation included proper stacking and securing of multiple HVAC components, connection of refrigerant lines via black electrical conduit, and integration with existing ductwork using flexible materials. Installed gray PVC condensate drain and vent piping running vertically through the installation area and extending to building exterior. Exterior PVC termination was properly configured with elbow joints to direct condensate flow away from foundation. All manufacturer specification labels and regulatory markings were verified and remain visible for future reference. System was mounted on concrete floor against interior wall with all connections properly secured. Installation completed to code with appropriate clearances maintained for service access.

Completed pre-winter heating maintenance on 3-year-old Lennox system. Performed comprehensive tune-up including inspection of furnace components, combustion analysis, and safety controls verification. Replaced heavily soiled air filters with new units to restore proper airflow and system efficiency. Inspected and serviced Aprilaire humidifier unit, checking water supply connections, drainage system, and electrical connections. All systems tested and confirmed operational for the heating season.

Conducted on-site assessment for furnace replacement. Evaluated existing aging furnace system showing visible wear, dust accumulation, and surface corrosion on associated piping. Documented current equipment configuration including ductwork connections, PVC condensate drainage system, and installation layout in basement mechanical room. Provided homeowner with replacement options and recommendations based on equipment condition and system requirements.

Responded to service call regarding high electric bills and potential AC system issues. Performed diagnostic inspection on both air conditioning units. Discovered failed capacitor on one unit exhibiting severe corrosion, burnt terminal connections, and electrical degradation from weather exposure. Tested electrical components with multimeter to verify capacitor failure and confirm system voltages. Identified the deteriorated capacitor as primary cause of system inefficiency, which would result in increased electrical consumption and reduced cooling performance. Recommended immediate capacitor replacement to restore proper system operation and reduce energy costs.

Responded to report of gas odor detected by technician and inspector during generator installation meeting. Conducted thorough inspection of exterior gas line connections and associated plumbing components, including brass shut-off valve with quarter-turn handle and flexible braided stainless steel supply line positioned near building foundation. Documented existing installations with photographic evidence for further evaluation and recommended follow-up gas leak detection service to ensure system safety and code compliance.

Responded to customer report of water leaking from ductwork in attic space. Upon inspection, observed moisture staining and discoloration on attic floor surfaces near ductwork area, indicating active or recent water intrusion. Documented conditions with photos showing affected areas and structural components for follow-up assessment and repair recommendations.

Responded to second call for upstairs air conditioning unit not cooling. Upon inspection, identified failed capacitor as the root cause of system malfunction. Replaced defective capacitor with new unit, verified all electrical connections at terminal block, and tested system operation to confirm proper cooling function restored.

Replaced O-zone bulb and ceramic plate in air purification system. Removed and inspected existing mesh filters during service, confirming proper airflow through ventilation components before completing installation.

Completed site assessment and electrical evaluation for backup generator installation. Documented existing electrical infrastructure including main service panel with dual rows of circuit breakers, transfer switch location, and current electrical service capacity. Inspected gas meter and utility connections to verify adequate fuel supply specifications for generator requirements. Photographed electrical panel configuration, available mounting locations, and existing utility meter setup to develop comprehensive installation proposal for automatic standby generator system.

Completed comprehensive tune-up on 4-year-old air conditioning system. Performed standard maintenance protocol including inspection of all major components, cleaned condenser coils, checked refrigerant levels and pressures, verified electrical connections, tested capacitors, and confirmed proper system operation. Inspected air filter which showed clean condition with proper airflow. During electrical inspection, identified terminal block with significant corrosion and oxidation on connection points requiring monitoring or future replacement to prevent potential system failure. All other components operating within normal parameters. System cooling effectively with no immediate concerns noted beyond the corroded terminal connections.

Completed preventive maintenance on two cooling systems as part of ongoing service agreement. Performed thorough inspection of air handler units, including examination of blower motor assemblies and verification of proper operation. Replaced air filters on both systems with new pleated media filters to ensure optimal airflow and indoor air quality. Inspected blower wheels and noted minor dust accumulation consistent with normal operation. Verified all electrical connections and wiring to motors were secure and functioning properly. Both systems tested and operating within normal parameters upon completion of maintenance procedures.

Completed scheduled preventative maintenance on residential cooling system. Replaced dirty air filter with new pleated filter to ensure proper airflow and system efficiency. Inspected and verified electrical connections on capacitor, confirming all wire terminals are secure and system is operating within normal parameters.

Responded to reported leak under gas water heater with visible water accumulation. Upon arrival, inspected Bradford White gas water heater unit and surrounding plumbing connections. Identified source of leak, performed necessary repairs to stop water discharge, and verified all connections were secure and functioning properly. Unit tested and confirmed operational with no further leakage detected.

Completed preventive maintenance on three residential cooling systems. Performed comprehensive inspection and service of indoor furnace units and outdoor condensing units, including filter checks, electrical connection inspections, refrigerant level verification, and cleaning of condenser coils. All systems operational and running within manufacturer specifications upon completion.

Completed comprehensive HVAC cooling maintenance on residential system under MVP preventative maintenance program. Performed thorough inspection of furnace unit and outdoor condensing unit, including examination of electrical components, capacitor, SureStart soft start device, control boards, and all wiring connections. All system components found to be operating within normal parameters with no deficiencies noted.

Replaced two UV bulbs in the HVAC system's air handler unit to restore proper air purification functionality. Verified system operation and confirmed thermostat was maintaining proper temperature setpoint at 68 degrees. Documentation photos were taken of the equipment and surrounding areas per customer request.

Completed HVAC system estimate for heat pump replacement at residential property. Accessed existing air handler unit located in attic crawl space to assess installation requirements and provide replacement options. Unit features horizontal configuration with copper refrigerant lines, PVC condensate drainage system with multiple shut-off valves, black drain pan, and electrical disconnect. Documented current equipment specifications, installation access points, and existing infrastructure including ductwork connections and clearance space for future replacement work.

Responded to service call for non-operational air conditioning unit serving bonus room. Upon arrival, located outdoor condenser unit heavily obscured by overgrown vegetation against building exterior. Accessed electrical compartment and inspected control wiring, connections, and internal components. Documented unit condition with equipment age unknown, while two other AC systems on property remained fully functional.