HVAC & Plumbing Services in Cleveland, OH

Performed an on-site evaluation of the furnace and surrounding utility area to prepare whole-home humidifier and indoor air quality (air purifier) options. Inspected the furnace cabinet, supply ductwork, gas piping, and available electrical service for suitable installation points, and documented equipment conditions with photos for estimate preparation.

Performed annual tune-up on a hot water boiler (approx. 7 years old), including inspection of the system pressure/temperature gauge and the burner assembly. Burner tubes were found with heavy carbon, rust, and debris buildup, and the boiler was operating properly at the time of service.

Performed a full diagnostic inspection on a 25-year-old upright furnace with no reported symptoms, evaluating the cabinet, burner and heat exchanger area, blower compartment, filter and access panels, and supply plenum and ductwork connections. Documented heavy dust, debris, and surface staining in the equipment area, along with visible corrosion on the adjacent pipe and loosely routed wiring near the unit, and noted that the aged furnace is operating well beyond its typical service life.

Performed a seasonal heating furnace tune-up, including cleaning and rinsing of serviceable components in the utility sink and an internal inspection of the furnace using an inspection camera to assess the interior condition. Inspected the heat exchanger and burner area, noting a fine dust coating and a rust-colored streak near a seam, and verified the system was serviced and ready for heating operation.

Performed scheduled heating maintenance on a gas furnace, including removal of access panels and visual inspection of the burner assembly, gas valve and piping, blower motor, pressure switch, flue connections, control board wiring, and condensate drainage components. Verified burners ignited and produced a proper flame pattern during operation, and confirmed the condensate pump and PVC drain line were in place. Noted loosely bundled wiring near the burner compartment as a recommended item for securing.

Performed seasonal heating maintenance, including inspection and replacement of the return air filter and a visual inspection of the furnace control board, wiring harness, and transformer. Confirmed the control board was powered with the status indicator lit, noted dust and debris accumulation in the furnace cabinet near the blower compartment, and verified the system was in operating condition.

Responded to a callback for a leaking pressure-reducing valve that was previously replaced and inspected the boiler feed piping, PRV, and associated fittings. Observed heavy corrosion and scale on the adjacent iron piping and joints, with the T&P relief valve and drain elbow also in the affected area. Documented conditions with photos for further evaluation and recommended repairs.

Installed a new 96% AFUE Amana condensing gas furnace with matching coil cabinet, elevated on concrete blocks in the mechanical room. Completed PVC combustion air/vent piping, condensate drain line, gas connection with shutoff valve, and ductwork transition, then installed the thermostat and humidifier connections and verified proper furnace operation, with all warning labels in place.

Serviced a legacy 1970s-era gas furnace reported to need a replacement thermocouple and gas valve. Inspected the unit and its control wiring, ductwork connections, and surrounding utility space to evaluate the safety pilot and gas control components. Documented the equipment condition with photos.

Performed scheduled heating maintenance on the gas furnace, including inspection of the burner compartment, burner tubes, and hot surface igniter, which was verified to heat and glow properly during the ignition sequence. Measured electrical readings with a clamp meter at the unit wiring to confirm normal operating current, and inspected the control board, wiring harness, and air filter rack for proper condition and secure connections.

Replaced the 3/4" radiator water valve on the cast-iron steam/hot water radiator, installing a new brass valve with threaded fittings and thread sealant at the connection to the radiator. Installed a Honeywell round thermostat to restore proper temperature control. Verified all joints are secure with no visible leaks.

Performed scheduled preventive maintenance on a gas-fired furnace, including inspection of the burner assembly, gas valve, inducer motor, and low-voltage wiring, with the upper access panel removed for a full component check. Verified the condensate drain assembly, vent piping, plenum, and duct transition seams were intact and sealed, and updated the equipment service record card. The unit showed no signs of rust, frost, or visible damage and was left in proper working condition.

Performed a seasonal heating tune-up on the hydronic boiler system, inspecting the combination pressure/temperature gauge, which read approximately 20 psi at 100°F with corrosion at its threaded brass fitting. Identified a heavily tarnished capped pipe stub with verdigris buildup and a visible crack along the cap seam, along with rust and oxidation on adjacent piping and a banded flue connection. Recommend monitoring the corroded fittings and cracked cap for potential leaks and replacing them as needed.

Performed scheduled preventive maintenance on the furnace, including inspection of the heating system and accessible flexible supply ductwork for condition and integrity. Removed and inspected the 16x25x4 pleated air filter and serviced the filter slot, with filter condition and replacement interval to be monitored as part of the recurring maintenance plan.

Evaluated the water boiler for a leaking heat exchanger and documented severely deteriorated, cracked combustion chamber insulation with soot and rust staining, along with heavy corrosion on the vertical piping and debris around the expansion tank in the mechanical room. Provided replacement and repair options for the boiler based on the findings.

Installed a new sub panel and dedicated circuit with an exterior-mounted, non-fused pull-out disconnect serving the HVAC condensing unit. Ran liquid-tight flexible metal conduit with secured clamps from the disconnect, terminated the conductors with proper color-coded wiring, and labeled the service equipment. Verified the disconnect operates correctly and left it in the OFF position with the cover closed and secured.

Installed a complete 90-90 side-discharge HVAC system, including a new Amana R32 condenser mounted on a rooftop equipment stand secured by concrete support blocks. Routed and secured refrigerant lines and electrical conduit to the unit, and verified the installation for proper placement, clearances, and system operation, with no visible damage or defects on completion.

Performed a heating-season tune-up, including electrical testing of the equipment with a true RMS clamp meter to verify component operation, and inspected the interior ductwork with a borescope camera. Noted corrosion on a pipe fitting and rust at a pipe section within the equipment cabinet, as well as debris and staining along the duct interior, and confirmed the 16x25x1 air filter specification for replacement.

Performed an on-site evaluation of the existing steam boiler installed in the basement mechanical area, inspecting the unit, associated black iron piping, galvanized flue/vent connections, and copper water lines for age-related wear, corrosion, and overall condition. Documented the installation with photographs and assessed replacement options for the steam system to be presented for review.

Performed seasonal maintenance on two heating systems, including inspection of the furnace cabinet, wiring, and gas piping connections and electrical testing with a clamp meter to verify proper component amperage draw. Checked the return air filter and measured temperature readings with a digital thermometer, noting heavy dust and corrosion buildup on the filter frame and adjacent fitting that should be monitored and addressed to maintain airflow and system efficiency.