Heating, AC & Plumbing Services in Moreland Hills

Completed comprehensive cooling maintenance on three HVAC systems. Performed standard seasonal maintenance procedures including inspection of electrical components, capacitors, and control systems with CoreSense diagnostic equipment. All systems inspected, tested, and confirmed operational with no deficiencies noted.

# Electrical Install - Generator Completed installation of an 18kW Generac standby generator system with full electrical integration. Mounted and wired automatic transfer switch (ATS) within new service panel enclosure, establishing proper connections between utility service, generator output, and load center distribution. Installed 200-amp rated disconnect with appropriate overcurrent protection and safety interlocks. Performed complete panel wiring including: - Main utility feed connections with proper phase identification - Generator input wiring to ATS with correct conductor sizing - Load side distribution to existing electrical service - Grounding and bonding of all components per NEC requirements - Installation of Generac control module with status indicators - Terminal block configuration for multiple circuit integration Verified proper wire routing and strain relief for all black, white, red, and green conductors entering top and bottom of enclosure. Secured all connections

Completed warranty coil replacement on residential air handler system. Removed and replaced defective evaporator coil assembly, installed new copper refrigerant line connections with proper brazing and soldered joints, and recharged system with refrigerant to manufacturer specifications. Verified all connections for proper seal, tested system operation, and confirmed cooling performance upon completion.

Completed scheduled cooling system maintenance on residential outdoor condensing unit. Performed comprehensive inspection of condenser assembly, verified protective grille cage integrity, checked electrical disconnect box and associated wiring connections, and examined refrigerant line routing. Unit showed normal weathering and environmental debris accumulation consistent with outdoor exposure. All components found to be operational and functioning within normal parameters.

Responded to service call for air conditioning system damaged by ice. Conducted thorough assessment of HVAC system and ductwork in attic space, documenting existing conditions including aged galvanized steel ductwork with visible wear, dust accumulation, and joint sealant deterioration. Provided customer with replacement options for damaged equipment. Created site sketch documenting property layout and equipment location for replacement planning purposes.

Performed routine preventive maintenance on residential air conditioning system. Inspected outdoor condenser unit, verified proper operation of fan motor and compressor, checked refrigerant lines and electrical connections for secure mounting and proper insulation. Unit found in good operating condition with adequate airflow through heat exchange coils and no visible signs of damage or system degradation.

Completed routine cooling maintenance on residential heat pump system as part of ongoing service plan. Performed system diagnostics including temperature measurements showing supply air at 58.9°F, tested refrigerant pressures at service ports, and inspected outdoor condenser unit for proper operation. Customer declined optional electrical inspection at time of service.

Completed comprehensive heating and cooling maintenance on multi-zone MVP system consisting of two heating units and two cooling units. Performed standard seasonal maintenance procedures including system inspection, electrical testing with digital multimeter, verification of proper airflow through ductwork, and assessment of condensate drainage system. All equipment found to be operating within normal parameters with no immediate service needs identified.

Performed scheduled cooling system maintenance visit. Upon inspection, discovered failed capacitor with visible physical damage including ruptured casing and corrosion at terminal connections. Replaced defective 20.0µF 440/370VAC dual run capacitor with new unit. Verified system temperatures using calibrated infrared thermometer, confirming proper operational parameters post-repair. System restored to full functionality and tested for proper cooling cycle operation.

Responded to report of water leak on one-year-old air conditioning unit. Performed thorough inspection of condensate drain system and identified source of leakage at primary drain line connection. Inspected PVC drain piping, trap assembly, and drain pan for proper installation and functionality. Observed buildup and residue in drain components indicating potential blockage or improper drainage. Checked condensate flow and verified trap was holding water seal as designed. Documented findings with photos for further review and determination of necessary repairs to resolve leak issue.

Serviced small 5-gallon Stiebel Eltron electric water heater installed in barn utility space. Inspected unit mounted on wooden platform below window, verified electrical connections at adjacent panel, and examined plumbing connections including flexible supply hoses with brass valve assembly at top of tank. Confirmed temperature control dial operation and indicator light functionality to prepare unit for summer use.

Responded to no cooling complaint on residential air conditioning system. Upon arrival, inspected outdoor condenser unit and indoor components including electrical controls and refrigerant connections. System evaluated for proper operation, refrigerant levels checked at service ports, and electrical connections verified at control panel. Unit restored to normal cooling operation.

Responded to service call for reported breaker and outlet issues. Upon arrival, conducted comprehensive electrical inspection of the property. During assessment, discovered significant environmental concerns in the basement utility area, including severe ice formation on overhead infrastructure, ductwork, and piping systems, indicating critical temperature control and moisture intrusion problems. These conditions posed potential safety hazards to electrical systems and could compromise circuit integrity. Documented all findings with photographic evidence showing ice accumulation on insulated ductwork, copper piping, and surrounding areas. Noted debris accumulation and general maintenance issues in basement and crawl space areas that could impact electrical component performance. Inspected electrical panels, breakers, and outlet circuits as originally requested. Recommended immediate attention to environmental controls and insulation systems to prevent electrical system damage and ensu

Installed compressor sound blanket jacket on outdoor condensing unit to reduce operational noise levels. Replaced system air filter to ensure proper airflow and maintain equipment efficiency. Documented installation with photographs showing compressor jacket properly secured to mounting bracket and existing refrigerant lines, electrical connections, and condenser coil configuration.

Responded to emergency no-cooling call on a residential split system approximately 4 years old. Upon arrival, inspected the non-functioning unit that had recently undergone pump replacement three weeks prior. Performed diagnostic evaluation of the affected system, checked electrical connections at the air handler location, and documented equipment condition. Verified warranty status on recent repairs and assessed overall system operation to determine root cause of cooling failure.

Completed comprehensive HVAC cooling system maintenance including inspection and servicing of the Aprilaire air treatment unit and blower motor assembly. Also performed hot water tank maintenance as part of the scheduled service visit.

Completed preventive maintenance on two cooling systems located in basement mechanical room. Performed comprehensive inspection of both HVAC units, including filter replacement, electrical connection verification, and system diagnostics using testing equipment. Checked condensate drainage systems, verified proper operation of all safety controls, and confirmed both units are functioning within manufacturer specifications for the cooling season.

Conducted comprehensive site evaluation for whole home generator installation at residential property. Assessed existing electrical infrastructure including gas meter location and utility connections on exterior wall. Documented optimal generator placement location on side yard, determining proper clearances of 2 feet from home structure and 3 feet from window opening to meet manufacturer specifications and local code requirements. Evaluated existing gas service accessibility and routing options for fuel supply connection. Photographed installation site conditions including foundation area, exterior siding, existing utility penetrations, and surrounding vegetation that may require trimming for proper clearance. Identified suitable location on grassy area adjacent to building with adequate access for equipment delivery and future maintenance. Assessed electrical panel accessibility for transfer switch integration and main service disconnect coordination. Documented site conditions inclu

Conducted site evaluation for generator installation at residential property currently equipped with existing HVAC systems. Assessed electrical service capacity, available installation space adjacent to existing condenser units on gravel pad, and determined optimal generator placement considering clearance requirements from equipment and structure. Documented existing electrical panel configuration, conduit routing, and transfer switch location requirements. Photographed current outdoor mechanical equipment layout including air handler, condensing unit, refrigerant line sets, and electrical junction boxes to develop comprehensive generator integration plan. Prepared detailed estimate for standby generator system installation including automatic transfer switch, gas line connection, concrete pad placement, and electrical connections to main service panel.

Responded to service call for air conditioning unit making unusual noise and experiencing extended cooling times. Upon arrival, performed diagnostic evaluation of outdoor condenser unit. Inspected ICM870-32A control module and associated electrical connections, noting multiple wiring connections to the system. Utilized digital clamp meter to measure electrical current and voltage readings, obtaining measurements of 381.4 volts to assess compressor and system performance. Evaluated condenser unit operation, including examination of exterior components and control box functionality to identify source of reported noise concern and cooling inefficiency.