Air Conditioning and Heating Services in Bay Village, OH

Removed the existing unit and installed a new 80% AFUE Goodman gas furnace with a matching A-coil on a raised concrete block base, connecting it to the existing supply and return ductwork. Installed new flue venting, condensate drain line, and gas supply with a shutoff valve, then tested for gas leaks and verified proper ignition, combustion, and airflow.

Performed an on-site evaluation of the steam boiler system and associated piping, including the automatic water feeder, pressure-reducing valve, isolation valves, and gas-fired water heater venting, and documented existing conditions with photographs. Identified oxidation and wear on components and developed repair options for the customer's review, with the maintenance agreement coverage to be applied toward the work.

Performed a no-heat diagnostic and replacement estimate on the gas furnace, inspecting the control compartment, White-Rodgers Intell-Ignition control board, gas valve, and associated wiring. Found loosely routed, tangled wiring with a spliced wire-nut connection, along with dust, grime, and rust or residue buildup throughout the cabinet, indicating the unit is aged and deteriorated. Presented furnace replacement options, including new flue piping, to restore reliable heating operation.

Responded to a thermostat fault in which the outdoor temperature sensor was reporting an erroneous 125°F reading. Inspection of the furnace and blower assembly found heavy rust and moisture staining on the galvanized blower housing and fasteners, along with dust accumulation, oxidation, and heat-discolored copper conductors on the motor assembly. The sensor fault and the observed corrosion and heat damage were documented with photos for further evaluation and recommended corrective action.

Performed annual furnace tune-up and inspection on a system less than five years old, including review of the gas supply piping, fittings, and pressure gauge, along with the electrical control cabinet and wiring. Noted surface corrosion and oxidation on the black iron gas piping and fittings, as well as cracked paint and mortar around the wall-mounted access panel, which should be monitored. Documented system condition with photos; the customer disputed the on-file equipment record, so unit age and model information could not be verified.

Performed scheduled preventive maintenance on the furnace heating system, including inspection of operation and verification of heating performance. Measured supply and return air temperatures with a digital thermometer, recording a supply temperature of approximately 140°F and a return temperature of approximately 80°F, indicating a temperature rise within normal operating range. System is operating properly with no deficiencies noted.

Performed seasonal heating and cooling tune-up, replacing the heavily soiled 16x25x4 return air filter with a new MERV 8 pleated filter to restore proper airflow. Inspected the outdoor condenser unit, cleared leaf debris from around the coil guard, and verified electrical operation using a true RMS clamp meter.

Performed a seasonal heating and cooling tune-up, inspecting the gas furnace's gas manifold, inducer assembly, pressure switches, control board wiring, and PVC condensate/vent piping, with all components operating normally. Noted surface rust and corrosion on the lower cabinet shelf and cluttered, aged wiring, and recommended monitoring for further deterioration.

Completed comprehensive heating system tune-up including inspection of all major components, electrical connections, and control board functionality. Verified proper operation of capacitors, examined wiring integrity throughout the system, and documented equipment condition with photographic records for maintenance history.

Completed scheduled heating maintenance on HVAC system. Performed thorough inspection of heat exchanger, confirming all fins were clean, properly aligned, and free of damage or debris accumulation. Examined blower assembly and squirrel cage fan, noting operational condition with minor dust buildup on blades. All components found to be functioning within normal parameters with no immediate repairs required.

# Electrical Estimate - Generator Installation Assessment Conducted comprehensive site evaluation for backup generator installation at residential property. Assessed existing natural gas meter assembly and utility connections mounted on exterior wall to determine compatibility and capacity for generator tie-in. Documented current gas line configuration, including meter positioning, pipe routing, and available connection points for future generator fuel supply integration. Performed basement inspection to evaluate electrical panel access and identify optimal routing path for generator transfer switch installation. Examined ceiling-mounted infrastructure including existing electrical conduit, HVAC ductwork, and plumbing systems to determine clearances and mounting locations for new electrical equipment. Assessed wooden joist structure and concrete block foundation walls for proper grounding and bonding requirements. Photographed all relevant utility connections, gas meter assembly, an

Completed preventive maintenance on three HVAC cooling systems. Performed comprehensive inspections of all units, including evaporator coil examination and refrigerant line assessment. Replaced air filters on applicable units with new pleated media filters to ensure proper airflow and system efficiency. All systems operational and check sheets documented per customer requirements.

Completed HVAC install warranty inspection and identified safety hazard at furnace disconnect switch junction box with missing knockout plug on side opening. Installed approved knockout plug/seal to properly close the opening and eliminate electrical shock hazard. Documented completed work with photos for reinspection verification.

# HVAC Maintenance Summary Completed routine cooling season maintenance on aging heat pump system as part of recurring preventive maintenance program. Performed comprehensive inspection of indoor air handler unit, assessed air filter condition showing moderate dust accumulation, and evaluated overall system operation. Documented equipment condition with visual inspection of condensate drainage system, electrical connections, and cabinet housing showing normal wear patterns consistent with system age. # Detailed Work Performed Conducted scheduled preventive maintenance visit on heat pump system over 10 years old located in basement utility area. Performed thorough visual inspection of indoor air handler unit, noting white metal cabinet housing with typical age-related surface discoloration and minor dirt accumulation on exterior panels. Inspected air filtration system, observing pleated rectangular filter with diagonal pleating pattern showing moderate dust and particulate loading.

Evaluated upstairs area for mini split installation options. Assessed two rooms including bathroom with existing radiator heating and bedroom with traditional radiator system and ceiling-mounted lighting. Documented current heating infrastructure and spatial layout to determine optimal placement for indoor air handling units. Provided customer with recommendations for ductless mini split configuration to supplement existing heating system in second-floor living spaces.

Responded to service call for thermostat displaying error message and unable to read outdoor temperature. Upon inspection, found blower wheel assembly heavily soiled with dust and debris accumulation affecting system operation. Measured supply air temperature at 53.1°F to verify cooling functionality. Diagnosed thermostat communication issue related to outdoor sensor malfunction and addressed system airflow concerns due to contaminated blower wheel and filter media requiring maintenance.

# HVAC Cooling System Maintenance Performed comprehensive cooling maintenance on residential split system with Amana furnace and outdoor condensing unit. Conducted electrical diagnostics using CoreSense testing equipment to evaluate capacitor performance, contactor operation, and electrical connections throughout the system. All electrical components tested within normal operating parameters. Inspected indoor air handler blower assembly and verified proper operation. Outdoor unit access panel removed for thorough inspection of electrical components, capacitor, and contactor. All wire connections checked and secured. System operational and functioning as designed upon completion of maintenance procedures.

# HVAC System Installation Completed full residential HVAC system installation featuring an 80% efficiency Amana furnace with matching air conditioning unit. Installed new furnace in utility room basement location with proper ductwork connections, including supply and return air plenums with metal ductwork distribution throughout the structure. Mounted air handler components near ceiling with secure support and verified all mechanical connections. Performed system startup procedures and diagnostic testing using calibrated instruments to verify proper operation, confirming system temperature differentials and electrical parameters within manufacturer specifications. All equipment operational and ready for service.

# HVAC Service Call - No Cooling Complaint Responded to service call for central air conditioning system with no cooling complaint. Upon arrival, contacted customer as requested and proceeded with system diagnostics. Performed temperature measurements at supply registers using calibrated digital thermometer. Initial readings indicated supply air temperature of 62.0°F at the register, suggesting insufficient cooling capacity or potential system malfunction. Normal supply air temperatures for properly operating AC systems typically range between 55-60°F with adequate temperature split from return air. Conducted visual inspection of HVAC equipment located in basement mechanical room. System consists of forced air furnace with integrated cooling coil and standard ductwork configuration. Equipment observed alongside residential water heater in utility space. All major components accessed and visually assessed for obvious signs of failure or operational issues. Documented equipment condi

# HVAC Cooling Maintenance Completed Performed comprehensive cooling system maintenance on residential air conditioning unit. Conducted thorough electrical diagnostics using digital clamp meter, measuring voltage and amperage at contactor terminals to verify proper electrical operation. Inspected terminal block connections, identifying multiple wires showing signs of age deterioration and frayed insulation on green and red conductors. All electrical connections were secured and verified for proper contact. Measured system performance parameters including voltage readings and current draw to ensure unit operating within manufacturer specifications. Inspected condenser coil and associated components for proper operation. System tested and confirmed operational upon completion of maintenance service.