Heating, AC & Plumbing in Chagrin Falls, OH

Performed routine maintenance and flush on an A.O. Smith ProLine XE tank-style, power-vent gas water heater. Drained the tank to remove sediment and mineral buildup, then restored the unit to service. Inspected the gas control valve, thermostat assembly, supply lines, venting, and drain pan, with no leaks or deficiencies noted.

Performed annual heating tune-up on a 9-year-old gas furnace, inspecting the gas valve assembly, wiring connections, and blower components. Found moisture and mineral residue on the interior panel, indicating condensation that should be monitored, and removed a heavily loaded pleated air filter that was restricting airflow and in need of replacement.

Performed scheduled heating maintenance on three furnace systems, including visual inspection of heat exchanger and coil components with a borescope camera and electrical testing of system components with a true RMS clamp meter. Noted surface rust on a metal component in one unit; systems were checked for proper operation and recommended for continued monitoring under the recurring maintenance plan.

Performed scheduled boiler maintenance, including inspection of the cast iron heat exchanger sections, which showed heavy dust and soot accumulation with surface corrosion on the fin edges. Opened the burner compartment and inspected the gas valve assembly, manifold, and burner tubes, cleaning soot and residue from the burners and orifices with a wire brush and verifying wiring connections at the gas valve were secure. Noted frayed cabinet insulation for monitoring and recommended follow-up on the corrosion at the heat exchanger.

Performed an on-site evaluation for replacement of an existing 33-year-old furnace, assessing the unit, the connected galvanized supply ductwork, and the exterior electrical service components. Documented the condition of the ductwork, including taped and mastic-sealed seams, a patched section, and minor surface corrosion, along with the exterior electrical enclosure and outlet locations, to determine the scope for a replacement installation.

Performed scheduled maintenance inspection of a three-unit gas water heater bank supplying the heated flooring system, including a visual assessment of vent/blower assemblies, gas control valves, T&P relief valve piping, and supply/return connections. Identified green oxidation and corrosion staining on the copper piping and fittings of one unit, along with rust-colored joints on the ferrous interconnecting piping and residue near the base of an adjacent unit, indicating possible minor weeping at connections. Documented conditions with photographs for the service record and recommended continued monitoring and corrective repair of the affected fittings.

Installed a new transfer switch and three load sheds to integrate the standby generator with the home's electrical system, enabling automatic switching between utility and generator power. Terminated all conductors and routed conduit from the meter enclosure to the service panels, then verified connections for proper operation.

Installed a new Amana heat pump condensing unit on a level composite pad as part of an oil-to-heat-pump system conversion, with refrigerant lines routed and insulated to the outdoor unit. Mounted and wired a DiversiTech electrical disconnect with flexible conduit to the condenser, with dedicated circuits supplied by the electrical contractor. The installed unit is clean and undamaged, with no signs of frost, rust, or leaks.

Replaced the water pressure reducing valve on the main supply line, installing a new brass PRV with a gate valve and flexible connectors to restore proper downstream pressure to the water heater and household fixtures. Noted corrosion at an adjacent pipe fitting and recommended monitoring it for future maintenance.

Completed warranty return visit to install replacement shower handle on existing valve assembly. Removed previous handle and installed new clear plastic control knob with proper seating against brushed metal escutcheon plate on white tiled shower wall, ensuring secure fit and smooth operation of valve mechanism.

Completed preventive maintenance on two heating systems as part of ongoing service plan. Performed comprehensive inspection of both furnace units, including verification of gas valve operation, electrical connections, and amperage draw readings. All components tested within normal operating parameters, with clamp meter confirming proper current flow at 91 amps. Both systems operational and ready for heating season.

Completed scheduled heating maintenance visit on residential furnace system. Performed comprehensive inspection of burner assembly, confirmed proper ignition and flame characteristics with all burners operating efficiently and producing consistent blue flames. Verified electrical performance using digital clamp meter, measuring amperage draw and system voltage to ensure components are functioning within manufacturer specifications at 0.00A standby and 55.3°F temperature readings. Inspected burner chamber, heat exchanger access area, and all visible wiring connections for signs of wear or deterioration. System operating properly with no deficiencies noted at time of service.

Completed comprehensive heating maintenance service on furnace system as part of ongoing preventative maintenance program. Inspected and verified operation of Aprilaire humidifier unit mounted on ductwork, confirmed proper integration with HVAC system. Performed temperature diagnostics throughout the home, recording ambient temperature readings of 72.95°F to verify system performance and proper heating distribution. All equipment found operating within normal parameters with no immediate service needs identified.

Responded to service call for tanked water heater with no hot water delivery to one side of the house. Upon arrival, inspected the White-Rodgers electronic control unit mounted on the water heater and observed status indicator lights showing green on cold side and yellow lights on heat side, indicating a control system malfunction. Diagnosed faulty temperature controller preventing proper heating element operation. Evaluated the complete plumbing configuration including copper supply lines, circulation pump assembly, and associated electrical connections. Verified proper gas supply and venting system integrity. Reset controller and tested heating elements to restore hot water distribution throughout the residence. Confirmed all safety systems operational and water temperature settings within manufacturer specifications.

Completed scheduled heating maintenance on residential furnace system. Performed diagnostic testing using digital manometer, recording pressure readings of 236 inWc to verify proper system operation. Inspected blower wheel assembly, confirming clean condition with no debris accumulation or blade damage, and verified all electrical connections and motor components are functioning within normal parameters.

Conducted comprehensive furnace replacement assessment and presented complete system options to homeowner. Evaluated existing HVAC equipment including outdoor condensing unit and current Honeywell programmable thermostat to determine compatibility requirements and provide full replacement specifications for heating system upgrade.

Installed new outdoor hose bib with proper freeze-proof configuration. Routed copper supply line from existing interior plumbing system through foundation wall to exterior mounting location. Completed installation includes shut-off valve for seasonal maintenance and secure mounting to prevent water damage.

Completed routine HVAC cooling maintenance visit, performing comprehensive system inspection and diagnostics. Conducted combustion analysis testing using calibrated instruments, recording efficiency readings and verifying proper operation of heating components. Inspected ductwork and identified significant dust and debris accumulation along seams and interior surfaces, documented conditions with photographic evidence, and assessed air filtration system status to ensure optimal indoor air quality and system performance.

Completed comprehensive electrical inspection of residential utility space. Documented electrical panel installation showing dual-row circuit breaker configuration with main disconnect assembly and verified proper wire routing and color coding throughout the distribution system. Photographed mechanical room infrastructure including HVAC ductwork, plumbing integration, and electrical components to provide visual record of current installation status and system layout for future reference.

Completed fall maintenance tune-up on a 4-year-old Goodman furnace system that was reported to be operating properly. Performed comprehensive inspection of all furnace components including the gas manifold assembly, burner array, heat exchanger, blower motor, and electrical connections. Verified proper operation of all safety controls, tested ignition system functionality, and confirmed adequate airflow throughout the system. All components found to be in good working condition with no repairs required at this time.