HVAC & Plumbing Services in Cleveland, OH

Performed routine maintenance flush on Lochinvar tanked water heater unit located in basement mechanical room. Drained sediment buildup from tank bottom through drain valve to improve heating efficiency and extend equipment lifespan. Inspected all plumbing connections, insulated supply lines, and pressure relief valve for proper operation. Confirmed adequate clearances around unit and verified drain pan placement. System refilled, tested for leaks, and returned to normal operation with improved performance.

Replaced refrigerant sight glass and serviced condensate drain line on HVAC system. Installed new brass valves with shutoff controls and verified proper refrigerant flow visibility through sight glass. Applied thread sealant to all connections and tested system operation to ensure proper drainage and no leaks.

Completed preventive maintenance on two cooling systems in preparation for property sale. Performed standard inspection procedures including filter access verification, air handler component assessment, and documentation of equipment condition. All systems operational and ready for listing.

Completed estimate for mini split installation to condition upstairs bedroom and attic space in home currently served by forced air system. Assessed attic room with sloped ceilings and existing window AC unit, evaluated electrical panel capacity and breaker availability for new mini split system, and documented site conditions for equipment sizing and placement recommendations.

Responded to second service call and successfully replaced failed PSC blower motor with new run capacitor after diagnosing leaking and failing bearings, and replaced failed inducer motor to restore full system operation. Unit tested and confirmed operational with proper burner ignition sequence and airflow.

Responded to no heat call on aging furnace system. Upon inspection, identified blower motor assembly with worn electrical connections and accumulated dust buildup affecting system operation. Diagnosed motor wiring configuration, verified proper electrical connections, and assessed overall condition of blower assembly and housing components to restore heating functionality.

Performed comprehensive assessment of aging furnace system located in basement utility area. Upon arrival, found unit to be over 50 years old with significant wear and deterioration evident throughout the equipment. Conducted thorough inspection of furnace cabinet, heat exchanger, blower assembly, and all associated ductwork connections. Evaluated mechanical components including motor, pulley system, and electrical connections. Assessed condition of metal ductwork and flexible piping throughout the system. Documented current state of equipment with photographic evidence showing unit mounted on platform with various storage items in surrounding area. Provided professional evaluation and discussed repair versus replacement options with homeowner, who was already aware of the system's advanced age and likely need for replacement. Recommended full system replacement due to age, efficiency concerns, and potential safety considerations associated with equipment of this vintage.

Responded to service call for Samsung mini-split system with reported refrigerant leak and no cooling. Upon inspection, discovered significant corrosion on outdoor unit copper piping and heat exchanger assembly, with visible oxidation on U-bend configuration and brass fittings. Documented condition of wall-mounted indoor evaporator unit and corroded outdoor condenser coil assembly mounted under elevated structure. Photographed leak source areas and provided assessment of system condition for repair recommendations.

Completed routine heating maintenance on Lennox heat pump system, model G33-360-2F. Performed comprehensive inspection of indoor air handler unit, verified proper operation of all electrical components and connections, checked refrigerant evaporator section, and inspected associated PVC condensate drainage system for proper flow and positioning. All equipment found operating within manufacturer specifications with no deficiencies noted.

Performed diagnostic testing on boiler system to evaluate incoming water pressure and assess pressure reducing valve (PRV) functionality. Left access key on-site for pressure testing to determine if PRV replacement will resolve the low water pressure issue affecting boiler operation. If PRV does not correct the problem, further evaluation and repair options will be provided to address the underlying water supply concern.

Completed plumbing inspection of residential property addressing bathtub drain seal failure preventing water retention and toilet base leak causing floor water damage in main bathroom. Documented existing plumbing conditions including washing machine supply line configuration with shut-off valves and filtration system, as well as utility sink faucet assembly with dual handle controls.

Replaced three existing column-style cast iron radiators with new thin tube radiators in attic bedroom and two second-floor bedrooms. Removed old radiator units, installed modern thin tube replacements, and connected to existing piping system. All new radiators tested for proper operation and heat distribution upon completion.

Completed scheduled heating maintenance on residential gas furnace system. Performed comprehensive inspection of all internal components including heat exchanger, blower motor assembly, gas valve manifold with distribution connections, pressure switches, and safety controls. Verified proper operation of ignition system, flame sensor, and all electrical connections throughout the unit. Inspected condensate drainage system including PVC piping, valves, and discharge lines for proper flow and secure connections. All components found operating within manufacturer specifications with no issues identified.

Performed comprehensive evaluation of existing boiler system and associated piping infrastructure dating from the 1970's era. Assessed aged copper distribution piping showing significant oxidation and patina, finned heat exchanger components, and overall system configuration within basement mechanical space. Documented current conditions of HVAC ductwork, electrical panel integration, and plumbing connections to provide multiple replacement options for outdated heating system and deteriorated piping network.

Performed scheduled heating system maintenance on boiler unit. During inspection, discovered wasp present in equipment housing and accumulated debris in lower equipment tray, which were addressed to ensure proper system operation. All mechanical components, piping connections, and safety controls were inspected and found to be functioning within normal parameters.

Responded to no hot water complaint at residential property. Upon arrival, inspected tanked water heater system in unfinished basement area. Completed diagnostic assessment and documented existing conditions of installation location and surrounding mechanical space for service records.

Completed comprehensive heating system maintenance on residential furnace unit. Performed standard inspection of furnace components, ductwork connections, and associated mechanical systems including water treatment equipment and piping assemblies. All systems operational and maintenance documentation updated on service record card.

Completed comprehensive heating system maintenance on Carrier air handler unit. Inspected and verified proper operation of AprilAire whole-home humidifier system, confirming digital control display reading 44% relative humidity with all indicator lights functioning correctly. Checked humidifier water panel condition, electrical connections, and control settings. Examined air handler cabinet, verified manufacturer specifications, and inspected all associated ductwork connections. Assessed condensate drainage system and PVC piping for proper operation and secure connections. All components found operating within normal parameters with no service requirements indicated at time of inspection.

Completed scheduled boiler maintenance inspection and diagnostics. Performed combustion analysis using digital testing equipment, recording temperature and efficiency readings to verify proper operation and safe combustion levels. All systems tested within normal operating parameters.

Responded to no heat call with furnace displaying 7-flash error code. Upon arrival, confirmed thermostat was calling for heat but system was not operating. Diagnosed fault code, identified issue, and restored heating operation to the system.