Air Conditioning, Heating, and Plumbing Services in Hudson, OH

Completed installation of new 96% efficiency furnace system with integrated Carrier humidifier unit. Installation included proper venting configuration using white PVC piping with multiple elbow joints routed through basement ceiling area, connection to existing ductwork infrastructure, and mounting of humidifier to supply plenum. All components tested and verified operational upon completion.

Completed comprehensive heating maintenance service on residential furnace system. Performed thorough inspection of control board and electrical connections, verifying proper operation of Emerson control module and all associated wiring harnesses. Measured and documented temperature readings at key system points, with discharge temperature recorded at 337°F indicating proper heat exchanger operation. Inspected all terminal connections, verified secure wire terminations across multiple circuits, and confirmed control board functionality. System operating within normal parameters with no issues identified.

Conducted diagnostic evaluation and presented furnace replacement options to homeowner. Assessed existing HVAC system including thermostat operation and inspected utility area where furnace equipment is located, noting visible water staining on floor near plumbing connections that may require attention during installation.

Responded to service call for 18-year-old Carrier furnace repeatedly tripping the circuit breaker. Upon inspection, discovered significant rust and corrosion throughout the unit's cabinet and base, along with deteriorated internal components consistent with the age of the equipment. Evaluated the blower motor assembly, electrical connections, gas valve, and refrigerant lines. Given the extensive corrosion, age of the unit, and safety concerns related to the breaker tripping issue, recommended full system replacement rather than repair due to the likelihood of additional component failures and potential safety hazards.

Completed comprehensive heating system maintenance inspection. Examined and tested electrical components including 20 MFD capacitor, control board connections, and flame sensor assembly, verifying proper operation of all safety controls and electrical terminals. All components found in satisfactory working condition with no repairs required at this time.

Responded to no hot water complaint following recent furnace installation. Upon arrival, investigated potential conflicts between newly installed heating system and existing tanked water heater operation. Inspected gas line connections, electrical wiring, and venting configurations to identify any disruptions to water heater functionality caused by furnace installation work.

Completed installation of new 96% AFUE high-efficiency furnace in basement mechanical room. Connected all ductwork, installed PVC venting system, and verified proper operation of unit alongside existing water heater. All components tested and system commissioned successfully.

Performed routine cooling system maintenance on residential HVAC unit. Upon inspection, discovered significant accumulation of dust, dirt, and debris on evaporator coil fins, particularly concentrated in center and right sections which can restrict airflow and reduce system efficiency. Cleaned evaporator coil thoroughly to restore proper heat transfer capability. Conducted electrical diagnostics using clamp meter at outdoor unit, recording amperage readings of 46.4A and 0.08A to verify compressor and system component operation within manufacturer specifications. Inspected condensate drain line, electrical connections, and control board for proper function. System restored to optimal operating condition with improved airflow through clean coil assembly.

# HVAC First Year Cooling Maintenance Completed Performed comprehensive first-year cooling maintenance on residential HVAC system. Conducted thorough inspection of furnace and control system components, documenting internal conditions of both the main heating unit and electronic control assembly. Examined circuit boards, wiring connections, and electrical components within the control panel, verifying proper connections and component integrity. Inspected furnace interior including gas valves, burner assembly, blower motor, ventilation piping, and associated wiring harnesses. All components found to be in operational condition with normal wear patterns. System maintenance completed as scheduled with photographic documentation of equipment condition for service records.

Accessed crawl space to extend existing 1/2" copper drain line to floor drain. Installed ProPress 90-degree elbow fitting onto copper drain pipe and added 3-4 feet of copper pipe extension to complete proper drainage connection.

# Condensate Drain Pump Water Leak Repair Responded to water leak in residential utility area caused by malfunctioning condensate drain pump. Upon arrival, found active water pooling on concrete floor surrounding pump assembly with visible moisture damage on adjacent wall surfaces. Diagnosed failed condensate pump unable to properly evacuate water from HVAC system, resulting in overflow condition. Inspected existing white PVC drainage piping configuration with red valve assembly and verified proper downstream drainage pathway. Examined electrical connections and flexible discharge hose for blockages or disconnections. Replaced defective condensate pump unit with new assembly to restore proper water removal function. Reconnected black flexible discharge hose and white PVC intake piping to new pump housing. Verified pump motor operation and confirmed proper cycling when water level activated float switch. Tested system under load to ensure adequate pumping capacity and no leakage at

Conducted on-site assessment of existing heating system in residential property to provide replacement estimate. Evaluated current furnace installation in basement utility area, documented existing Honeywell digital thermostat controls, and photographed mechanical room layout including ductwork configuration and available space for new equipment installation. Provided homeowner with equipment options and pricing for complete heating system replacement.

Performed comprehensive AC system inspection and drainage verification. Inspected HVAC unit, condensate drain lines, and all associated piping connections to ensure proper operation and drainage functionality. Confirmed system is operating within normal parameters with no drainage issues detected.

Responded to customer report of furnace leaking extensively. Upon inspection, identified issue originating from evaporator coil assembly and associated condensate drainage system in attic installation. Examined A-coil configuration with serpentine copper refrigerant lines and finned heat exchanger, noting proper coil orientation but potential drainage concerns. Inspected condensate drain lines including PVC piping and connections in confined utility space beneath unit. Assessed drain pan condition, P-trap functionality, and primary/secondary drain line routing. Documented system configuration and leak source with photographic evidence for service records and recommended corrective action to resolve water intrusion issue.

Conducted comprehensive sump pump replacement estimate for failed unit in basement installation. Assessed existing system including corroded copper discharge piping with significant oxidation at elbow joint, PVC vertical discharge pipe, and basin configuration with standing water present. Documented complete failure of current pump and evaluated discharge line condition showing advanced deterioration requiring replacement alongside pump unit.

Completed comprehensive cooling tune-up on Carrier air conditioning system, including inspection of outdoor condenser unit and indoor air handler. Performed standard maintenance procedures, verified system operation, and documented equipment condition with photos. Customer expressed strong interest in enrolling in preventative maintenance membership program for ongoing system care.

Performed coil cleaning on outdoor condensing unit to remove accumulated dirt and debris that had built up on the heat exchanger surfaces, restoring proper airflow and heat transfer efficiency. Replaced failed turbo capacitor to restore proper compressor and fan motor operation, ensuring the system could cycle normally and maintain optimal cooling performance.

Completed routine HVAC cooling maintenance visit as part of recurring preventive service program. Performed standard system inspection, took temperature readings showing 57.6°F at measurement point, and documented outdoor unit components including refrigerant lines, conduit routing, and ground-level equipment condition. System operating within normal parameters with no repairs required at this time.

Performed comprehensive generator maintenance including battery system testing and diagnostics. Battery analyzer confirmed optimal performance with 100% state of charge, 825 CCA test pass rating, and 3.63mΩ internal resistance. All maintenance procedures completed successfully with system operating within manufacturer specifications.

Completed comprehensive cooling system tune-up and inspection. Performed visual inspection of electrical components including Inteli-ignition control board and capacitor (CAP050300440CS), verified all wire connections secure and properly terminated. All system components found operating within normal parameters.