Heating, AC & Water Heater Services in Lakewood, OH

Completed installation of three-zone mini-split system with outdoor condenser unit and indoor air handlers. Installed refrigerant line sets with proper insulation, established electrical connections and dedicated circuit, mounted outdoor unit on platform against building exterior, and ran condensate drainage. System was pressure tested, evacuated, charged with refrigerant, and fully commissioned with all zones operational and performing to manufacturer specifications.

# Electrical Panel and Knob-and-Tube Wiring Assessment Conducted comprehensive evaluation of existing electrical system requiring complete rewire due to obsolete knob-and-tube wiring throughout the structure. Inspected aging fuse panel with multiple circular fuse holders showing deteriorated condition with disorganized wiring configuration. Documented extensive tan-colored cloth insulation on conductors indicating original installation dating back several decades. Panel exhibited overcrowded wire management with insufficient capacity for modern electrical demands. Assessed exterior electrical service entry point on brick facade, including meter base installation and existing conduit routing. Evaluated service entrance configuration to determine requirements for new panel replacement and updated electrical distribution system. Photographed current conditions to document scope of work needed for full electrical system modernization including generator installation preparation. Provide

Completed routine plumbing maintenance inspection on Bradford White Defender Safety System water heater. Performed visual assessment of unit condition, verified proper operation of safety systems, inspected copper supply lines and brass fittings for leaks, and documented installation with date marking for maintenance tracking purposes.

Responded to service call for Carrier air conditioning unit experiencing intermittent condenser fan operation. Upon arrival, performed diagnostic testing of the outdoor condenser unit using digital multimeter. Measured capacitor microfarad reading of 21 MFD, which indicated capacitor failure as the original specification was significantly higher. Further testing confirmed voltage readings of 34.3 volts at the fan motor terminals. Diagnosed failed run capacitor as root cause of condenser fan shutting off prematurely. Replaced defective dual run capacitor with properly rated OEM replacement part. Verified correct microfarad ratings for both compressor and fan motor circuits. Tested system operation through complete cooling cycle to ensure condenser fan maintained continuous operation without interruption. System restored to normal operating condition with proper airflow across condenser coil.

Completed cooling system tune-up on Unico high-velocity HVAC system. Performed temperature diagnostics at supply register using calibrated digital instrumentation, verifying proper airflow and system performance. Provided customer education regarding blower wheel maintenance, emphasizing the importance of regular filter replacement and system upkeep to prevent future efficiency loss and potential component failures.

Conducted on-site evaluation and provided furnace replacement options for residential heating system. Assessed existing gray metal furnace unit installed in basement utility area with white PVC exhaust venting system and documented current equipment configuration including associated water heater. Reviewed electrical service panel requirements and photographed existing installation to support equipment replacement recommendations and ensure proper system specifications for future installation.

Completed routine HVAC cooling system maintenance on residential unit. Performed thorough inspection of blower motor assembly and squirrel cage fan, verified proper operation of all electrical connections and motor components, and confirmed system functionality with no deficiencies noted.

Completed comprehensive whole home plumbing inspection, examining all accessible fixtures, supply lines, and drainage systems throughout the property. Documented toilet tank interior condition showing mineral deposits and discoloration requiring future maintenance attention, and inspected mechanical systems including ductwork and associated plumbing connections in utility areas. All findings photographed for record and future reference.

Completed preventive maintenance on two cooling systems. Inspected and documented the condition of both units, including evaporator coils, refrigerant lines, and heat exchanger components. The wall-mounted unit's evaporator coil showed significant dust and debris accumulation requiring attention, while the second system's heat exchanger coil and refrigerant tubing displayed moderate dirt buildup typical of operational wear. Both systems were evaluated for proper operation and component condition as part of routine maintenance protocol.

Conducted comprehensive on-site evaluation of existing residential HVAC system and water heating equipment to provide full system replacement options. Assessed current dark gray furnace/air handler unit and GE-branded cylindrical water heater located in basement mechanical room, documenting equipment specifications, condition, and installation configuration including all associated ductwork, venting, and piping connections. Presented customer with multiple equipment replacement options for both heating/cooling system and hot water heater to facilitate informed decision-making for complete system upgrade.

Completed scheduled cooling system maintenance on residential HVAC unit located in basement mechanical room. Performed comprehensive inspection of furnace and cooling components, including blower motor, electrical connections, and capacitor. Verified proper operation of all system components, checked wiring harnesses and control circuits, and documented equipment condition through photographic records for maintenance history.

Conducted site evaluation for mini split air conditioning installation in residential property currently equipped with boiler heating system. Assessed multiple rooms including living/dining areas with existing radiator heat, documented spatial layout and electrical requirements, and photographed potential indoor unit locations to prepare comprehensive estimate for ductless AC system addition.

Completed preventive maintenance on two HVAC cooling systems. Performed comprehensive inspection of both units, including temperature measurements using calibrated infrared thermometer to verify proper system operation and airflow temperatures. Inspected furnace units, ductwork connections, condensate drainage lines, and electrical components. All systems found operating within normal parameters with no deficiencies noted.

Completed scheduled preventive maintenance on residential cooling system. Performed electrical diagnostics using digital multimeter to verify proper voltage and amperage readings at the air handler and ductwork connections. All electrical components tested within manufacturer specifications, and system confirmed to be operating efficiently with no deficiencies noted.

Completed scheduled cooling system maintenance on residential HVAC unit. Performed comprehensive inspection of air handler assembly, including blower motor, fan wheel, and electrical connections. Verified proper operation of control board and all associated wiring terminals. Measured amperage draw using clamp meter, confirming system operating within manufacturer specifications at 104.26 amps DC. Inspected condensate drain system and PVC piping for proper drainage. All components found to be functioning correctly with no immediate service needs identified.

Completed scheduled maintenance on a Daikin ductless mini-split cooling system. Accessed and inspected air filters, which showed normal dust accumulation from regular operation. Verified proper mounting and operation of the wall-mounted indoor unit, confirming system functionality and readiness for continued cooling performance.

Completed HVAC install warranty service addressing refrigerant line issues. Identified and repaired small leak in lineset, installed missing locking caps on service ports, and corrected improper line configuration where only one line was properly connected instead of the required two lines. Verified system integrity and proper refrigerant line connections upon completion.

Responded to no cooling complaint on recently installed system. Upon inspection, found severely restricted airflow due to heavily soiled air filters with significant dust and debris accumulation. Removed and documented multiple hexagonal-frame pleated filters showing substantial contamination that was impeding system performance and preventing adequate cooling capacity.

Completed cooling tune-up on multi-zone Mitsubishi Electric heat pump system consisting of 2 outdoor condensing units serving 9 total indoor air handlers. Inspected both outdoor units, verified proper operation of electrical contactors and relays, checked refrigerant line connections, and confirmed all components functioning within normal parameters.

Responded to customer report of insufficient cooling from air conditioning unit. Upon arrival, connected manifold gauges to measure system pressures and diagnose the cooling issue. Performed pressure and temperature readings on the refrigerant system to assess operational parameters and identify the root cause of reduced cooling performance.