HVAC & Air Quality Services in Mayfield Heights, OH

Performed annual maintenance tune-up on a 2-year-old Amana gas furnace with a Space-Gard air cleaner. Inspected the unit and verified supply air temperature at the duct using a digital thermometer, confirming proper heating operation. The system is functioning properly, with no visible rust, frost, or damage observed.

Performed scheduled heating maintenance on a gas furnace, inspecting the inducer motor, pressure switches, silicone and rubber hoses, wiring harness, and burner assembly with the access panel removed. Components showed light dust accumulation but no signs of rust, frost, or breakage, and the system was found in good operating condition. Reviewed the importance of blower wheel cleanliness and regular filter replacement to maintain efficiency, airflow, and indoor air quality.

Performed scheduled heating maintenance on the furnace, inspecting the inducer motor assembly, pressure switch, and associated wiring connections. Noted surface corrosion on the inducer motor housing and a heavily soiled pleated filter at the electronic air cleaner section, with the filter removed for replacement. Recommend monitoring the inducer motor for continued corrosion and maintaining regular filter changes to ensure proper airflow and system efficiency.

Installed a 24kW Generac standby generator with an automatic transfer switch on the exterior wall, running #2 THHN aluminum feeder conductors in conduit with Unistrut support. Terminated and torqued all connections to manufacturer specifications, connected the control module and low-voltage wiring, bonded the neutral and ground, and completed the gas line connection from the existing meter assembly.

Performed a heating-season tune-up on the HVAC system, inspecting the air handler interior and flexible hose/line connections and noting buildup on the cabinet surfaces. Verified heating operation by measuring supply air temperature at the floor register, which read 120°F, confirming proper heat output.

Installed GFCI outlets and a dedicated sump pump outlet in basement utility area. Addressed main electrical service panel issues and corrected exposed wiring hazards, ensuring all connections meet current electrical code requirements.

# HVAC Heating Maintenance Service Completed comprehensive heating system maintenance on residential furnace unit. Performed thorough inspection of air handler assembly, including examination of air filter condition and housing integrity. Filter showed proper installation within black frame assembly with all mounting hardware secure. Verified condensate collection pan condition and drainage pathway, noting normal operational moisture levels. Conducted detailed electrical diagnostics using digital multimeter to verify system voltage and control board functionality. Measured line voltage at 253.1 volts, confirming proper electrical supply to unit. Inspected control board for any signs of component failure or connection issues, with all wire terminals and connectors properly seated. Tested safety circuits and verified proper operation of all electrical connections including red, white, blue, and green control wiring. Examined refrigerant line connections and brass fittings for any sign

Performed diagnostic evaluation on aging B.K. Wadsworth furnace system presenting with heat exchanger failure. Unit is out of warranty and requires replacement due to compromised heat exchanger integrity, which poses safety concerns. Provided customer with furnace replacement options and estimates for new equipment installation, including assessment of existing ductwork connections and PVC venting configuration in basement mechanical room.

Responded to no heat call on 21-year-old Trane furnace (model TUD100R936K5) where system was producing cooling instead of heat when thermostat called for heating. Upon inspection, diagnosed reversed thermostat wiring causing improper system operation. Corrected thermostat wire connections to restore proper heating function. Conducted system operational test to verify furnace now responds correctly to heating demand. Given the advanced age of the unit, advised customer of system's condition and recommended planning for replacement in the near future due to expected end of service life for equipment of this vintage.

Completed comprehensive preventative maintenance on eight furnace units located in crawlspace areas. Performed standard heating season inspection protocol including filter inspection and replacement, blower motor examination, electrical connection verification, and burner assembly assessment. All systems evaluated for proper operation and safety compliance prior to heating season demands.

Conducted site assessment for mini split installation in two-story residential property with attic bedroom and standard bedroom spaces. Evaluated existing heating infrastructure including baseboard unit in attic space and confirmed electrical requirements for ductless heat pump system installation, coordinating with electrical contractor for necessary outlet and power supply modifications to support new HVAC equipment.

Completed scheduled heating maintenance on residential furnace system. Performed comprehensive inspection of blower motor assembly and electrical connections, verifying proper wire terminations and secure mounting. Inspected flame sensor assembly and cleaning access, confirming proper positioning and functionality. All components operating within normal parameters with no issues identified during preventative maintenance visit.

Responded to no-heat call on furnace over 10 years old that would not ignite. Performed diagnostic testing using digital multimeter to check voltage and electrical connections at the control board and ignition system components. Identified faulty flame sensor preventing burner ignition, cleaned sensor rod, verified proper microamp reading, and tested system through complete heating cycle to confirm successful ignition and operation.

Responded to a clogged bathroom drain service call where the customer reported a blockage in the bathroom sink or drain. Upon arrival, assessed the bathroom plumbing system and determined that a long snake auger would be required to effectively clear the obstruction, as recommended by the installation department. Successfully cleared the drain blockage and restored proper drainage function to the bathroom fixture.

Completed mini-split system installation including outdoor condenser unit placement on equipment pad with proper clearances, line set installation through wall penetration with protective cover, and dedicated electrical circuit connection. Unit positioned on side of residence with adequate airflow access, all refrigerant lines properly insulated and secured, electrical conduit run from meter to disconnect and condensing unit. System tested and operational, balance of payment collected upon completion.

Performed on-site electrical estimate for 22kW standby generator installation. Evaluated existing electrical service infrastructure, including current meter assembly and service entrance configuration. Conducted comprehensive load calculation analysis using gas meter sizing documentation to verify adequate utility capacity for proposed generator system, confirming total BTU requirements of 329,618 with existing household appliances, HVAC equipment (112,000 BTU furnace), and generator load (187,668 BTU). Documented existing electrical panel location and service entrance equipment through site photography for engineering review and permit application preparation.

Completed annual maintenance and tune-up on an 11-year-old boiler system. Performed comprehensive inspection of all components, including heat exchanger, burner assembly, and control systems. Verified proper operation and combustion efficiency. Additionally provided on-site consultation and pricing estimate for future mini-split system installation as requested.

Responded to no cooling complaint following recent maintenance visit. Upon arrival, performed electrical diagnostics using clamp meter to measure amperage at outdoor unit components, including capacitor circuit. Tested system airflow and temperature readings at ductwork using digital gauges to verify operational parameters and identify cause of cooling failure.

Completed routine preventive maintenance on residential cooling system. Performed comprehensive inspection of control board and electrical connections, verified proper voltage readings at 24.7V on low-voltage control circuit, and confirmed all wiring terminations were secure with no signs of overheating or degradation. All system components operating within normal parameters.

Completed scheduled preventive maintenance on residential Goodman split-system air conditioning unit. Performed comprehensive inspection of outdoor condensing unit including visual examination of cabinet, coil condition, and fan operation. Inspected indoor air handler components and verified proper airflow through existing mesh filter assembly. All system components found operating within normal parameters with no deficiencies noted at time of service.