Heating, AC & Plumbing Services in Mentor, OH

Responded to a no-heat call on a Goodman gas furnace with an attached evaporator coil installed two months prior. Removed the lower access panel and inspected the control board, low-voltage and line-voltage wiring, gas piping, venting, and condensate drain assembly with pump to diagnose the failure to call for heat. No visible damage, corrosion, or frost was found, and the unit was left with the service tag attached.

Installed a complete high-efficiency HVAC system consisting of a 96% AFUE gas furnace, a Goodman air conditioning condenser, and a whole-home humidifier. The condenser was set level on a composite pad with a new insulated refrigerant line set, flexible electrical conduit, a fused disconnect, and a PVC condensate drain routed to code. The system was verified for proper operation, and the installation was left clean with no visible damage.

Performed an on-site evaluation for replacement of an existing forced-air HVAC system, inspecting the furnace/air handler cabinet, supply plenum and ductwork, condensate drain piping, and installation area. Documented existing conditions, including cabinet and duct wear, efflorescence and staining on the concrete slab indicating prior moisture exposure, and unit clearance measurements (approximately 33 inches) to determine sizing and installation requirements. Reviewed AC replacement options for the customer and noted site conditions to be addressed prior to installation.

Performed an on-site evaluation of an approximately 40-year-old cast iron boiler in the basement utility area to determine replacement and upgrade options. Inspected the boiler controls, aquastat and pressure/temperature gauge, electrical disconnect, flue connection, and the aged copper and black iron distribution piping, noting heavy oxidation and tarnish throughout the system. Documented existing conditions, including clearances and venting, with photographs to support the replacement options presented to the customer.

Completed comprehensive heating tune-up and safety inspection on Weil-McLain boiler system for new homeowner. Performed full operational assessment including burner inspection, heat exchanger examination, flue gas analysis, and pressure testing of all piping connections. Verified proper operation of pressure relief valve, circulator pumps, and zone controls. Inspected all copper supply and return piping for leaks and corrosion, noting existing patina on older copper lines consistent with system age. Tested ignition system, flame sensor, and all safety controls to ensure proper shutdown sequences. Confirmed adequate combustion air supply and verified proper venting. System found to be operating within manufacturer specifications with no immediate safety concerns or required repairs at time of inspection.

Conducted comprehensive assessment of 17-year-old Bryant furnace system in ranch home basement and identified critical heat exchanger failure requiring immediate replacement. Presented full HVAC system replacement options to address safety concerns and provided detailed estimate for new equipment installation, including proper sizing calculations for the existing ductwork configuration and condensate drainage system.

Completed heating tune-up service on HVAC system. Performed electrical diagnostics using clamp meter, recording voltage and amperage readings to verify proper system operation. Inspected blower motor assembly, capacitors, and all electrical connections for optimal performance and safety compliance.

Completed pressure reducing valve replacement and PVC line repair to restore proper water pressure regulation to the residential plumbing system. Installed new dishwasher with supply line connections and drain hookup, ensuring proper mounting and leveling. Configured and installed water supply line for new refrigerator ice maker and water dispenser connection, including shut-off valve installation for future maintenance access.

Conducted on-site evaluation of existing residential electrical panel originally installed in 1992 for potential upgrade. Inspected main breaker panel configuration, documented current circuit breaker layout across dual columns, and assessed overall panel condition and capacity. No deficiencies or operational issues were identified during inspection; evaluation performed at homeowner's request to determine upgrade options for aging electrical distribution system.

Completed comprehensive heating maintenance visit on residential furnace system. Performed standard diagnostic testing using digital measuring instruments to verify proper system operation and efficiency. Replaced air filters with new pleated media filters to ensure optimal airflow and indoor air quality for the upcoming heating season. All equipment tested and operating within manufacturer specifications.

Completed scheduled heating maintenance visit on residential furnace system. Performed comprehensive system diagnostics including electrical measurements using digital multimeter to verify proper voltage and amperage across blower motor and control circuits. Inspected all wiring connections, blower assembly, ductwork, and mechanical components with all systems found operating within normal parameters.

Completed estimate for single-head mini split system in commercial facility. Assessed existing wall-mounted indoor unit, refrigerant line set installation, and electrical connections for repair requirements. All necessary equipment and materials were available on-site to access and service the system.

Completed comprehensive heating tune-up on Amana HVAC system, including inspection of all major components, control boards, and electrical connections. Verified clean air filter installation, checked thermostat operation, and confirmed proper system functionality. All circuit boards, wiring harnesses, and blower motor components inspected and found in good working condition with no issues identified.

Responded to no cooling call at commercial facility. Upon arrival, found wall-mounted ductless mini-split system not operating. Diagnosed issue, performed necessary repairs to restore cooling function, and verified proper system operation before departure.

Performed comprehensive preventive maintenance on residential cooling system. Conducted electrical diagnostics using digital multimeter, verifying voltage readings and testing system components at the outdoor condensing unit. Inspected all electrical connections, refrigerant lines, and return air grille, confirming proper operation and system integrity throughout.

Responded to plumbing service call at vacant residential property for multiple leak issues in basement. Assessed and addressed water pressure reducing valve (PRV) leak showing significant corrosion and deterioration on curved pipe section. Inspected drain pipe leak in basement area with bucket positioned to catch water. Evaluated sump pump discharge system on exterior back left side of building, identifying cracked PVC pipe requiring repair at 90-degree elbow joint connection. Documented all affected plumbing components with photographs showing extent of corrosion on metal piping and damage to exterior drainage system. Provided assessment and repair recommendations for corroded PRV assembly, basement drain leak, and compromised sump pump discharge line to prevent future water damage.

Performed comprehensive heating maintenance on 11-year-old Carrier Infinity electric heat pump system per customer request for furnace check-up. Inspected outdoor unit mounted beneath deck structure, including disconnect box and electrical components. Replaced cartridge fuses in outdoor disconnect to ensure proper electrical protection. Examined indoor air handler electrical controls and safety devices, including thermal switches and associated wiring connections. All system components inspected, electrical connections verified secure, and unit returned to proper operating condition.

Conducted comprehensive electrical assessment for grounding system evaluation and outlet repair. Inspected main electrical panel, documenting circuit breaker configuration, wire routing, and grounding connections, and examined basement/crawl space area including exposed ceiling joists and PVC conduit runs to assess overall electrical infrastructure condition and identify necessary corrections for proper grounding and outlet functionality.

Completed scheduled heating maintenance on furnace system. Performed comprehensive system diagnostics using digital multimeter to verify electrical parameters and circuit integrity, with readings confirming proper voltage and amperage within manufacturer specifications. Conducted temperature differential measurements at supply registers using infrared thermometer, recording 70.2°F at vent outlet. Inspected all electrical connections, gas lines, and mechanical components for proper operation and safety compliance. System tested and operating normally with all parameters within acceptable ranges.

Responded to callback for ductless mini-split system displaying blue indicator light after being powered off during cooler weather. Connected manifold gauges to outdoor condensing unit and performed system diagnostics. Verified refrigerant pressures, checked electrical connections at disconnect box, and inspected indoor wall-mounted air handler. System operating normally with no refrigerant loss or mechanical issues detected; blue light was part of normal startup sequence and cleared after system stabilization.