Heating, Cooling, Plumbing Services in Reminderville, OH

Completed HVAC tune-up service on residential system. Performed temperature measurements on ductwork, recording 74.3°F readings to verify proper air distribution. Inspected air filter condition, which showed satisfactory cleanliness with minimal debris accumulation in the fibrous media.

Conducted on-site evaluation of existing HVAC system to assess cooling capacity concerns and provide replacement options. Inspected indoor air handler unit located in attic space, including blower assembly, filter housing, and condensate drain configuration. Evaluated outdoor condensing unit condition, noting weathered exterior casing and examining condenser coil fins for debris accumulation and operational wear. Documented current equipment specifications from manufacturer data plate for proper sizing calculations. Photographed existing system components to support replacement recommendations addressing undersized equipment concerns. Provided customer with multiple equipment options for system replacement to achieve adequate cooling capacity for the residence.

Completed comprehensive HVAC tune-up service on residential cooling system. Performed electrical diagnostics using clamp meter, confirming proper amperage draw of 5.78A and voltage reading of 88V at the compressor circuit. Inspected dual-run capacitor (FASCO 440/370VAC) and associated wiring connections, verifying all terminals secure and components functioning within normal parameters.

Responded to no-cooling complaint on 7-year-old Amana system. Upon arrival, found outdoor condenser unit surrounded by overgrown vegetation and tall grass restricting airflow to unit. Cleared vegetation from around condenser to restore proper airflow and prevent future operational issues. Unit had been powered off overnight by customer prior to service call. Verified system operation after clearing obstructions and restoring power.

Conducted diagnostic evaluation of existing HVAC system in basement utility area. Assessed current equipment condition, documented system specifications and manufacturer information from unit labels, and provided customer with replacement options based on findings. Repair diagnostic fee applied to service call.

Performed seasonal AC start-up and cooling maintenance on system that was installed during cold weather conditions when initial operation was not possible. Tested and verified proper electrical operation of condenser unit components including capacitor function and amperage draw using digital multimeter, confirming all readings within manufacturer specifications. Measured refrigerant charge at 6.25 oz to ensure proper system capacity and optimal cooling performance for the upcoming season.

Completed comprehensive MVP cooling system maintenance on residential HVAC unit. Performed standard preventive maintenance procedures including inspection of all mechanical and electrical components, blower motor assembly, gas valve connections, and control board functionality. Verified proper refrigerant temperatures using digital thermometer, recording operating temperature of 67.8°F at the evaporator coil. Inspected copper line connections for oxidation and proper sealing, examined all wire terminations and electrical connections at control board and motor assembly, and confirmed secure mounting of all internal components. All systems tested and operating within normal parameters upon completion of maintenance service.

Completed annual preventative maintenance visit on residential air conditioning system. Performed comprehensive system diagnostics including electrical testing with multimeter to verify proper voltage and amperage at compressor and condenser unit, and measured supply air temperature at 48.3°F confirming adequate cooling performance. All components operating within manufacturer specifications.

Responded to service call for circuit overloading issues caused by tank heater and EV charger exceeding panel capacity. Performed electrical load assessment and determined existing breaker configuration was insufficient for increased power demands. Reconfigured circuit breakers within main electrical panel, relocated and balanced circuits to distribute load more effectively across available phases. Installed whole-home surge protection device to protect electrical system and connected equipment from power surges. Verified all breaker connections, torqued terminals to manufacturer specifications, and tested system under load to ensure stable operation. Updated panel directory with accurate circuit labels for dryer, AC units, and other major appliances. All work completed to NEC standards with proper wire sizing and overcurrent protection in place.

Responded to no cooling complaint on residential air conditioning system. Upon arrival, performed diagnostic inspection of HVAC equipment including furnace/air handler unit and associated components. Inspected condensate drain system with PVC piping, verified proper installation of safety switches and pressure relief mechanisms. Documented equipment condition through photographic records showing furnace cabinet, ductwork connections, copper refrigerant lines, and auxiliary components in mechanical space.

Installed a new Rinnai tankless water heater unit on a wall-mounted plywood backing board secured to brick wall. Completed all copper piping connections, installed isolation valves, ran PVC venting through wall penetrations, and connected electrical conduit and gas line to ensure proper system operation.

Installed dedicated 120V electrical outlet with junction box and conduit to provide power supply for new tankless hot water heater installation. Ran electrical wiring through protective conduit along basement wall, properly secured junction box to concrete block wall, and verified all connections meet code requirements for wet location appliance power supply.

Responded to emergency service call for water heater leaking onto basement floor. Upon arrival, conducted thorough inspection of A.O. Smith tanked water heater system and associated plumbing connections. Identified source of leak, assessed condition of unit, pressure tank, and circulation pump assembly mounted on top of water heater. Documented existing installation including PVC supply and drainage lines, shut-off valves with red and blue handles, and overall mechanical system configuration for service records.

Completed comprehensive cooling maintenance on Goodman HVAC system, model GKSB07DCBBAA. Performed standard inspection procedures, verified manufacturer specifications and electrical ratings (115V, 60Hz, 1Ph), and documented unit serial number for new customer service records.

Completed first-year cooling maintenance on residential air conditioning system as part of annual service plan. Performed comprehensive inspection of condensing unit, verified refrigerant charge levels on A2L refrigerant system, checked service valve operation, inspected copper line sets and insulation for proper condition, examined condensate drainage system with funnel trap assembly, and documented equipment specifications. All components found operating within normal parameters with no deficiencies noted.

Completed first-year preventative maintenance visit on furnace system under annual service plan. Performed comprehensive inspection of blower motor assembly, verified proper operation of squirrel cage fan wheel, and examined all electrical connections including motor wiring harness. All components found to be in satisfactory working condition with normal wear patterns observed.

Performed comprehensive maintenance on residential furnace system, including inspection of blower motor, electrical connections, and gas line components. Verified proper operation of PVC venting system and checked integrity of ductwork connections and condensate drain lines. All components functioning within specifications; system is operating efficiently with no issues detected.

Performed routine heating maintenance service including temperature verification (169°F) of system components and inspection of blower motor assembly. Checked electrical connections and verified proper operation of all system components.

Performed scheduled annual maintenance on furnace system. Inspected PVC flue pipe connections and clamps for proper sealing. Cleaned flame sensor with abrasive pad and checked electrical connections throughout system to ensure proper functionality.

Performed routine heating tune-up service on HVAC system. Conducted diagnostic testing with Testo 310 analyzer, confirming proper combustion parameters with delta P reading of 14. Inspected control board and wiring connections, verifying all components were properly secured and functioning correctly.