HVAC & Air Quality Services in Shaker Heights, OH

Performed routine maintenance service on Goodman heating system with attached humidifier. Inspected all components including ventilation system, PVC piping, and electrical connections. System functioning properly with no issues identified.

Performed electrical inspection of residential service entrance components and main distribution panel. Examined exterior meter installation on brick facade, verifying proper conduit connections and mounting. Inspected interior circuit breaker panel, evaluating breaker condition, wire routing, and overall system integrity.

Diagnosed no-heat complaint in furnace under 10 years old, finding condensation on heat exchanger and burner assembly. Inspected blower motor and determined it was operational, but discovered ignition failure due to moisture contamination. Cleaned affected components, verified proper ignition sequence and confirmed normal heat output before completing service.

Responded to customer call regarding water leakage from boiler system. Upon inspection, identified compromised sight glass component in the hydronic loop as the source of the leak. Replaced sight glass assembly and checked system pressure, confirming proper operation with no further leakage observed.

Performed routine maintenance on primary furnace covered under MVP service agreement. Inspected ventilation components showing normal dust accumulation and verified proper wire connections through the control panel. Secondary AC unit was operational but not included in current service plan.

Conducted site assessment for ductless mini-split replacement options. Inspected existing Fujitsu wall-mounted thermostat and evaluated current ductwork condition in attic space. Documented insulated metal ducts and structural considerations for potential system conversion.

Completed installation of a new furnace system with proper gas line connections and PVC ventilation. Installed and configured an Aprilaire humidity control panel with digital display, connecting all necessary wiring. System was tested and is functioning at optimal performance levels.

Performed routine maintenance on residential heating system, including inspection of burner assembly, motor components and electrical connections. Checked and cleaned interior components, removing accumulated dust and debris to ensure optimal system operation. All connections were verified and system was tested for proper functionality.

Conducted site assessment for AC replacement options as existing unit has been non-operational for extended period. Documented exterior utility connections and electrical service equipment. Inspected mechanical room revealing corroded copper piping with valve and ventilation ductwork. Noted furnace is relatively new and in good working condition.

Performed routine heating maintenance on a furnace system. Inspected electrical connections, terminal blocks, and wiring for proper installation and function. Unit appears well-maintained with properly installed PVC intake/exhaust venting and no visible issues with the air handler or connected components.

Performed scheduled heating maintenance on P.R. Wadsworth furnace system. Conducted pressure testing with manometer showing 0.62" reading on gas supply, confirming proper operation. Inspected ventilation system including PVC exhaust components; all connections secure with no issues detected.

Conducted assessment of HVAC system with inoperable furnace and water heater due to compromised chimney liner causing severe leakage into the heating system. Inspection revealed water damage to the utility area with visible staining on cinder block walls and evidence of moisture affecting the mechanical components. Presented replacement options for both heating system and water heater that would address the chimney liner compatibility issues.

Conducted site assessment at residential property to provide furnace replacement options due to high repair costs on existing unit. Inspected exterior HVAC condenser unit and electrical connections, noting accumulated debris around the unit. Verified electrical service via the Centron digital meter to ensure proper power supply for potential replacement equipment.

Performed scheduled monthly heating system maintenance which included inspection and replacement of dirty pleated air filter. System components including barcode-labeled mechanical parts were examined for proper operation. All systems functioning normally after service.

Responded to service call for non-functioning thermostat. Diagnosed and replaced faulty Ecobee smart thermostat with new unit. Successfully calibrated system and verified proper heating function with temperature display showing accurate readings and flame icon indicating normal operation.

Performed scheduled heating maintenance service on residential gas furnace system. Inspected and tested all internal components including blower motor, electrical connections, and control board. System is functioning properly with no issues identified; all ventilation and condensate lines are properly connected and in good condition.

Successfully installed a new 96% efficiency furnace (model ARVT961205DN) with humidifier, and modified the return air system by closing one side of a double return. Full payment was collected via check upon completion of the installation.

Performed assessment for Unico system replacement with existing boiler heat. Inspected current installation space including storage area with equipment and small utility closet with access panel. Documented site conditions for proper system specification and installation planning.

Performed routine maintenance on basement boiler system, including inspection of water heater, expansion tank, and associated copper piping network. Checked all valves for proper operation and examined ductwork integrity throughout the utility area. Documentation of equipment specifications completed for service records.

Performed scheduled maintenance service on multiple heating systems including two furnaces and one boiler. Conducted operational performance procedure (OPP) on the boiler system. Inspected electrical control panel components and connections, checking wiring integrity and control board functionality. Examined basement mechanical room equipment including furnace/air handler unit, associated ductwork, and plumbing connections to ensure proper system operation.