HVAC & Air Quality Services in Shaker Heights, OH

Completed installation of ductless mini-split heat pump system with indoor wall-mounted air handler unit installed in living space and line set routed through basement utility area to outdoor condenser location. Electrical connection deferred to scheduled follow-up appointment per customer coordination requirements.

Responded to no cooling call with thermostat displaying "open start circuit" error. Upon inspection, tested the run capacitor using a digital MFD tester which confirmed capacitor failure with abnormal readings. Replaced defective dual run capacitor, verified all electrical connections were secure, and confirmed system returned to normal operation with error cleared.

Responded to return service call for frozen window AC unit. Upon arrival, allowed system to fully defrost before conducting inspection. Examined evaporator coil assembly and refrigerant lines, noting copper piping configuration and insulation condition. Identified significant corrosion and rust buildup on pipe joints and connections, particularly at coupling points where moisture accumulation had caused surface deterioration. Documented deteriorated metal components with photographic evidence showing oxidation patterns and compromised pipe integrity. Unit successfully defrosted and inspected for underlying causes of freeze-up condition related to corroded components and potential airflow restrictions.

Responded to no cooling complaint and diagnosed failed blower motor assembly with severe corrosion damage to housing and internal components. Removed deteriorated blower unit showing extensive rust on metal framework and cracked plastic housing, replaced with new assembly, and restored proper airflow to system.

Completed HVAC estimate for air conditioning system replacement in residential property. Assessed existing basement mechanical room infrastructure, including electrical panels, ductwork configuration, and available space for new AC installation. Documented current conditions of utility area showing aged electrical systems, existing furnace with overhead ductwork, and water heater to determine compatibility and requirements for new cooling equipment integration with existing HVAC infrastructure.

Responded to callback for recurring E2 error code on whole-home dehumidifier unit that was previously serviced. Inspected dehumidifier control board, electrical connections, and drainage system to diagnose the service required error message. Documented system configuration with air handler and dehumidifier installation, verified proper wiring connections and flexible ductwork connections to both units.

Completed comprehensive electrical inspection of residential property, examining both interior utility area and exterior electrical service equipment. Interior inspection focused on basement electrical systems, including evaluation of conduit installations, junction boxes, and proper code compliance of exposed wiring runs along structural framing. Exterior inspection involved thorough assessment of main electrical service panel, meter housing, circuit breaker configuration, and associated conduit connections. Verified proper installation of PVC and metal conduit systems connecting utility components. Documented current conditions of all electrical equipment with photographs for record-keeping purposes. All observed systems were evaluated for safety and code compliance.

Completed comprehensive cooling maintenance on two HVAC systems. Performed diagnostic testing on both units, including temperature and humidity measurements using calibrated digital instrumentation to verify proper system operation. Inspected ductwork installations in attic space, examining flexible and rigid duct sections, insulation integrity, and proper sealing of all connections. All systems found operating within normal parameters with no deficiencies noted.

Replaced HVAC air filter with new 20x25 pleated filter to maintain proper system airflow and efficiency. Verified thermostat operation and confirmed system cooling properly at 69 degrees.

Returned to residential location to complete warranty capacitor replacement on outdoor condensing unit. Removed failed capacitor and installed new Breeze33 dual run capacitor, reconnecting all color-coded wiring leads to proper terminals. Verified secure electrical connections and proper wire routing within equipment cabinet before restoring unit to service.

Performed preventive maintenance on outdoor condensing unit found with significantly obstructed airflow due to heavy vegetation overgrowth and debris accumulation on condenser coils. Cleared dense plant growth from around and through unit housing, removed dirt and debris buildup from mesh grille and cooling fins, and restored proper clearance around equipment to ensure adequate ventilation and optimal system efficiency.

Responded to no cooling complaint on rooftop HVAC unit. Upon arrival, performed diagnostic evaluation of condensing unit and system operation. Documented equipment condition and rooftop installation with photos showing unit placement, electrical disconnect, and surrounding rooftop environment for service records.

Completed scheduled preventive maintenance on residential cooling system. Performed standard inspection of air handler unit, replaced air filters with new pleated media filters, and verified proper airflow through the system. Measured and recorded refrigerant temperatures using digital testing equipment, confirming system operating parameters were within normal range at 67.2°F. All components inspected and found to be functioning properly with no issues identified during this maintenance visit.

Responded to no cooling complaint for upstairs unit in a dual-zone residential system. Customer reported inadequate cooling to second floor while downstairs unit operated normally, along with water leakage from one unit damaging furniture. Upon arrival, performed diagnostic inspection of both HVAC systems to identify the source of cooling failure and water intrusion issue affecting the upstairs zone.

Completed preventive maintenance on two residential cooling systems as part of ongoing service plan. Performed comprehensive inspection of furnace and air handling equipment, verified operational parameters, and documented system readings with digital instrumentation showing 638°F at measurement point. All equipment found operating within normal specifications with no deficiencies requiring immediate attention.

Completed air conditioning system add-on installation to existing furnace in basement mechanical room. Unit installed and connected to ductwork system, with electrical work coordinated and finalized. System tested and operational, with balance collected upon completion.

Performed routine cooling maintenance on outdoor Unico air conditioning system. Inspected electrical components including contactor, capacitor, and wiring connections within the control compartment, and evaluated overall unit condition including fan assembly and exterior housing. Appointment was rescheduled from original date to complete the preventive maintenance service.

Responded to service call for attic air conditioning unit causing water leakage through kitchen ceiling in three locations following recent maintenance visit. Inspected evaporator coil and condensate drainage system, identifying blocked condensate drain line as source of overflow. Cleared obstruction from primary drain line, verified proper drainage flow, and tested condensate pump operation. Examined condenser coil fins and blower motor assembly for any installation issues from previous service. Confirmed system cooling properly with no refrigerant leaks and all components operating within manufacturer specifications.

# HVAC Cooling Maintenance Summary Completed routine cooling system maintenance on residential Amana HVAC unit located in basement utility area. Performed comprehensive inspection of furnace and air conditioning components, verified proper operation of all system controls, and documented temperature readings at supply ductwork measuring 55°F, confirming adequate cooling performance. # Detailed Service Report Performed seasonal preventive maintenance on residential forced-air cooling system with Amana brand equipment. Conducted thorough visual inspection of furnace cabinet, verifying all manufacturer labels and safety warnings remained intact and legible. Inspected PVC intake and exhaust vent piping for proper connections, secure mounting, and absence of blockages or damage. Examined sheet metal ductwork connections to main unit, confirming structural integrity and proper sealing at joints. Verified electrical connections and copper refrigerant lines showed no signs of damage, corro

Completed scheduled cooling maintenance on Unico high-velocity HVAC system. Performed comprehensive inspection of blower module, verified proper operation of 1/2 HP motor, checked electrical connections at 120/208-230V specifications, inspected refrigerant lines and insulation integrity, and confirmed all safety labels and manufacturer specifications were clearly visible and equipment was operating within normal parameters.