HVAC & Air Quality Services in Shaker Heights, OH

Responded to no-heat call at Susan's residence. Accessed basement utility area through exterior cellar entrance. Inspected boiler system and associated components including expansion tank and connected piping. Identified issue and restored heating functionality.

Performed scheduled contract maintenance on boiler system. Inspected anchoring hardware and verified proper mounting of the equipment to the foundation. Examined sight glass assembly and associated brass fittings, confirming proper fluid levels and absence of contaminants. All components functioning within normal parameters.

Successfully installed a new boiler system with integrated hot water tank in the utility area. Completed all necessary copper piping connections, installed expansion tank, and ensured proper gas line connections with appropriate valves. System was tested and is functioning according to specifications.

Performed inspection on aging boiler system with suspected gas issue. Determined shut-off valves require replacement. Advised customer to keep boiler offline until repairs can be completed to ensure safety.

Performed routine maintenance on residential heating system. Inspected Aprilaire humidifier mounted to furnace, checked all electrical connections, and verified proper operation of pressure switches. System is functioning properly with no issues identified.

Conducted comprehensive plumbing inspection of outdoor water supply system. Examined PVC piping configuration and identified areas of water damage where pipes penetrate ceiling. Observed potential leak indicators including white mineral deposits at pipe joints and inspected insulation integrity on water lines.

Successfully installed new high-efficiency boiler system with comprehensive piping network including galvanized and copper components. Connected all necessary supply lines, return pipes, and installed circulation pump (red component). System was fully tested and is operating at optimal performance.

Performed scheduled heating maintenance service. Inspected ductwork, electrical connections and control systems. System functioning normally with all indicator lights operational; no issues requiring repair were identified.

Responded to emergency service call for 10-15 year old furnace not staying on after recent power outage. Inspected system, replaced dirty air filter, and reset control board. System now operating properly with stable flame and normal heating cycle.

Performed scheduled boiler maintenance service. Inspected control panel showing normal operating temperature (032), checked system pressure which registered at approximately 17-18 PSI (within acceptable range), and verified proper operation of all safety limit controls. All components functioning correctly with no issues identified.

Replaced faulty shut off valve, installing new chrome angle stop with stainless steel braided supply line. Ensured proper connection to wall fixture and verified no leaks upon completion.

Performed scheduled maintenance on residential tanked water heater system. Inspected unit, expansion tank, and associated copper piping for proper operation and potential issues. All components functioning normally with no concerns identified.

Conducted full system replacement assessment of aging Amtaire HVAC system located in basement utility area. Presented three-tier heat pump and air handler replacement options featuring progressively improved efficiency ratings (up to 8.2 HSPF/17.2 SEER) and warranty coverage. Customer also requested inclusion of electrical panel upgrade in final quote.

Diagnosed no-heat complaint by performing electrical diagnostic testing on pressure switches and control board. Checked voltage at gas valve assembly and verified proper operation of ignition sequence. System restored to normal operation after resolving faulty electrical connection.

Performed scheduled boiler maintenance service including comprehensive inspection of system components. Conducted combustion analysis using Testo 310 analyzer, verifying proper operation with readings of 16.9% and 22.6% recorded. All parameters confirmed within manufacturer specifications; system operating efficiently.

Performed scheduled boiler maintenance service. Inspected electrical connections and found all terminals secure with proper wire routing. Checked system pressure gauge reading approximately 18-20 PSI, which is within normal operating parameters for this boiler system.

Completed heating maintenance service including inspection of blower wheel assembly and control board. Verified proper electrical connections on the circuit board (CN5T2-D) and examined fan components for functionality. All systems checked and operating normally.

Responded to customer-reported boiler leak. Inspection revealed significant corrosion and oxidation on multiple pipes in the boiler system, particularly on copper and iron components. Observed deterioration at pipe joints and ceiling penetrations with evidence of long-term moisture exposure. Identified mixed materials from previous repairs contributing to system vulnerability.

Replaced faulty 8" zone damper in HVAC ductwork system as part of warranty service. New damper installed on horizontal silver duct to restore proper zone airflow control.

Performed scheduled maintenance on boiler heating system. Inspected unit components including safety controls and connections. Identified corrosion on copper elbow joint in the plumbing network that requires monitoring during next service visit.