HVAC & Air Quality Services in Shaker Heights, OH

Conducted inspection of electric garage heating system, specifically examining non-functioning radiators. Inspected electrical panel to verify circuit capacity and evaluated existing utility infrastructure in basement area. Prepared estimate for replacement of outdated electric radiator heating system in garage with new electric heating solution.

Performed scheduled maintenance on hydronic boiler system. Inspected copper piping network, verified proper operation of circulator pumps, and checked all brass valves and fittings. System is functioning within normal parameters.

Returned to property to replace defective gas valve on furnace as per warranty service. Removed existing valve assembly and installed new OEM replacement valve. Tested system operation after installation to confirm proper gas flow and ignition sequence.

Responded to emergency service call for steam leak. Located and repaired pin hole in cast iron radiator system that was actively releasing steam. Inspected and measured associated components to ensure proper system functionality after repair.

Performed scheduled maintenance on dual heating system installation consisting of 2 furnaces and boiler. Inspected heat exchanger, ductwork, and condensate drain lines. System components were found in good working order with minor dust accumulation noted on internal components. All connections and PVC ventilation piping verified secure with no leaks detected.

Performed scheduled maintenance on boiler heating system, including cleaning and replacing filter elements that showed significant sediment buildup. Drained and flushed system to remove accumulated debris and murky water, ensuring proper circulation and optimal heating efficiency.

Performed scheduled maintenance on residential boiler system. Inspected heat exchanger components and identified copper tubes with oxidation. Cleaned and serviced furnace unit, ensuring proper venting connections and insulation integrity on distribution piping.

Performed assessment of aging boiler system showing significant corrosion on vertical piping and connection components. Unit inspection revealed a furnace/boiler with visible wear, mounted on deteriorating concrete pad, with panel access issues and compromised copper plumbing connections. Presented customer with replacement options based on evaluation findings.

Performed scheduled maintenance on residential boiler system. Serviced copper piping components and inspected drainage system, confirming proper condensate collection into bucket. Completed all required preventative maintenance tasks per PSP Maintenance protocol.

Completed scheduled maintenance on a 6-year-old steam boiler system. Inspected Weil-McLain boiler unit, associated copper piping, and control systems including VXT module. Verified proper operation of brass valve assembly and pressure regulation components.

Completed water heater installation in basement utility area. Installed Bradford White unit with proper copper piping connections and ventilation system. Mounted expansion tank above unit and attached inspection tag to verify completed work.

Performed scheduled hot water tank maintenance service. Inspected residential water heater system including expansion tank, copper supply lines, and connection points. Unit appears to be in normal operating condition with no signs of leaks, damage, or unusual wear.

Performed routine heating maintenance on Amana furnace system. Conducted electrical diagnostics using UEi G2 Phoenix multimeter, measuring voltage parameters at 0.250/0.082. Replaced furnace filter and addressed humidifier warning light by inspecting Aprilaire water panel that required replacement.

Responded to no-heat complaint where customer reported boiler buzzing followed by heat failure. Upon inspection of the heating system components in utility area, found issue with boiler ignition sequence. Diagnosed and repaired faulty control valve, restoring proper operation and heat output to the residence.

Secured loose conduit fasteners on exterior electrical installation per inspector requirements. Verified proper attachment of both metal electrical conduit and accompanying cable runs along white siding. Documentation photos confirm completed remediation.

Performed scheduled maintenance on boiler system. Inspected control board circuitry and all wire connections for proper function. Removed and cleaned flame sensor to ensure optimal ignition performance.

Performed scheduled maintenance on twinned furnace heating system. Conducted static pressure testing with UEI EM152 manometer showing 72.6 reading. Inspected ductwork, plenum connections, and refrigerant lines; all components functioning within normal parameters.

Performed scheduled maintenance on dual heating systems: boiler and furnace. Inspected heat exchanger components for proper operation, confirming clean flame pattern with appropriate blue coloration indicating complete combustion. Examined mechanical components including fan assembly and ventilation equipment, noting minimal dust accumulation and all systems functioning within normal parameters.

Responded to customer call regarding furnace heating issues. Upon inspection, discovered melted plastic filter causing heat exchange problems. Documented water damage near the unit suggesting possible condensate leak. System was shut down for safety; recommend replacement of damaged components and further assessment of water intrusion source.

Performed routine maintenance on two boiler systems. Inspected burner assemblies confirming proper flame pattern and combustion. Checked water levels and verified operational status of all control valves on both units.